03 Stability

L-Ornithine HCl: moisture, the pack and the shelf life

Technical document 03 · Reviewed 2026-11-20 · L-Ornithine HCl

On this page
  1. The powder: moisture, caking and chloride
  2. The solution is the exposed format
  3. What drives the change
  4. A protocol for the packed ingredient
  5. The finished formula changes the answer
  6. How the shelf life is set

L-Ornithine hydrochloride is a hygroscopic, acidic salt. The dry powder stores well in a sealed, moisture-barrier pack; once water reaches it, the powder cakes, the loss on drying rises and the as-is assay falls. In solution the same material meets heat, pH and microbial risk, and the shelf life has to be measured in the pack and the matrix that will be sold.

In one line

Moisture is the first failure mode for the dry salt; the solution adds heat and pH, and the shelf life belongs to the pack and the matrix.

The powder: moisture, caking and chloride

The catalog loss on drying is ≤0.5%. That is a release gate, not a storage allowance: an opened pouch in a humid room will move past it. The salt is hygroscopic, so water collects at the particle surface first, the fine 80 mesh powder bridges into lumps, and the as-is assay falls even while the dried-basis figure holds.

The chloride load makes the wet powder mildly corrosive. A damp spill left on mild steel, a scoop stored wet or a damaged liner is a handling and maintenance problem as well as a quality one. Keep the powder in the original foil pouch or an opaque, moisture-barrier container, keep the closure dry, and clean spills before they dry into the surface.

Heat accelerates the movement of moisture but is not the primary driver in a sealed pack. A hot loading bay or a car boot is still the wrong place for a hygroscopic salt; let a cold pack equilibrate before opening so that condensation does not form on the powder.

The solution is the exposed format

The salt dissolves freely and gives an acidic solution. The pH depends on concentration because the ammonium group is a weak acid; the catalog does not print a pH number for the salt, so a formulator who needs one should agree a value and a concentration in the specification and measure it on the lot.

In solution the risks are different from the powder: heat drives browning with reducing sugars, pH changes the ionisation and the taste, and an unpreserved aqueous system is a microbial risk. The chloride is still present, so a metal contact surface that was acceptable for a neutral syrup may not be acceptable here. A ready-to-drink process adds a pasteurisation or hot-fill step that the powder never sees.

If a liquid is unavoidable, fix the pH, control the heat load, preserve the system and validate the hold time in the real matrix. A bulk-powder result does not transfer to a drink.

What drives the change

What moves L-ornithine hydrochloride during storage
FactorEffectControl
MoistureCaking, higher loss on drying, lower as-is assaySealed foil pouch; dry filling room
HeatFaster browning and degradation in solutionCool process; validate the heat load
pHChanges ionisation, taste and solution stabilityAgree the pH; buffer or adjust the matrix
Reducing sugarsBrowning with heat in a liquid or a wet blendChoose low-sugar carriers; trial the matrix
Metal contactChloride corrosion; colour and metal pickupSpecify chloride-service contact surfaces
MicrobiologyGrowth in an unpreserved aqueous systemPreservation and process validation

A protocol for the packed ingredient

Run the study on the pack that will be sold. The standard long-term condition is 25 °C/60% relative humidity, with 30 °C/65% relative humidity for a hot, humid destination and 40 °C/75% relative humidity as the accelerated arm. Add an open-pack arm if the powder will be weighed in a humid filling room; that arm measures the pickup the closed pack is meant to prevent.

Test assay, specific rotation, loss on drying, appearance, chloride if it is a specification line, and microbiology at each point. The rotation should be stable; a change in it is a signal about the molecule, not about the water. Photostability is a smaller question for this salt than for a chromophore, but a clear container is still not the right pack.

Add a stressed sample of the real blend. A capsule shell, a tablet granulation and a stick pack each transfer moisture differently, and the blend can show caking or a pH shift before the powder assay moves.

The finished formula changes the answer

A capsule or tablet keeps water activity low, but the shell and the excipients can still move moisture into the fill. Check loss on drying, appearance and assay after storage, not only at release. A tablet granulation adds water and a binder; the granulated grade needs its own data.

A stick pack is a small, sealed environment. The acidic salt can change the drink pH, and any moisture that reaches the powder can cake it before the consumer opens the pack. The seal and the strip are part of the stability question, not only the powder.

A liquid combines pH, heat, preservation and chloride corrosion. The ingredient's bulk stability is the starting point; the shelf life of the drink has to be measured in the drink.

How the shelf life is set

We do not publish one shelf-life number for L-ornithine hydrochloride, because the pack and the storage condition set it. The assigned retest period belongs in the specification and is supported by the stability file for that pack, liner and closure. A number without those details is a claim, not a shelf life.

After the retest period, re-assay the retained sample before extending use. Do not carry a bulk figure across to a repack, and do not extend on the strength of the assay alone if the powder has caked or changed colour. The product hub lists the standard packs; the COA page covers the release tests; the MOQ page covers pack and lead time; the loss-on-drying note explains the moisture test; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation