06 Identity & adulteration

How we prove an L-lysine lot is the free base

Technical document 06 · Reviewed 2026-11-20 · L-Lysine

On this page
  1. Four checks, four questions
  2. The molecular-weight ratio and the chloride check
  3. XRD and the solid state
  4. Where substitutions show up
  5. Writing identity into the specification
  6. What to ask the supplier

A free-base L-lysine lot has to satisfy four checks at once: the paper names L-lysine and CAS 56-87-1, IR matches the reference, the rotation at c=2 in 5 M HCl is +25.0° to +27.0°, and the titration is 98.5–101.5% with loss on drying ≤0.5%. A chloride result near 19% would point to the hydrochloride. None of these lines is sufficient alone.

In one line

IR identifies the amino acid, rotation identifies the L enantiomer, titration measures the content, and the absence of chloride supports the free-base form.

Four checks, four questions

Each check answers a separate question, and none of them can be skipped. A supplier who answers only the first has sent a description, not evidence.

What each identity check establishes
CheckQuestionMethodWhat it establishes
Paper trailIs the form stated?Name, CAS number, formulaOnly what the documents say
IRIs it the right amino acid?Spectrum against a referenceThe functional groups
RotationWhich enantiomer is it?Polarimetry or chiral HPLCL or D
Mass balanceIs it cut, or salted?Titration, water, chlorideContent and form agree

The molecular-weight ratio and the chloride check

The ratio between the forms is fixed by their formulas. The free base is 146.19 g/mol and delivers 1.00 g of lysine per gram. The hydrochloride is 182.65 g/mol and delivers 146.19 ÷ 182.65 = 0.800 g of lysine per gram; chloride makes up the other 19.41%. The ratio does not move with the assay or with the batch.

Lysine and chloride in one gram of each form
LineL-lysine free baseL-lysine hydrochloride
Molecular weight146.19 g/mol182.65 g/mol
Lysine per gram1.00 g0.800 g
Chloride per gramNone as the counter-ion0.194 g

A lot sold as the base with chloride near 19% is the salt, or a blend containing it. A lot sold as the salt with little chloride is not the salt, however high the titration reads. A blend sits between the figures in proportion to its salt fraction. The solution pH is a supporting signal: the salt is specified at 5.0–6.0, while the base is alkaline.

XRD and the solid state

XRD looks at the crystal, not at the content. It can show whether the solid is crystalline, whether the pattern matches a reference, and whether two sources have the same solid form. It cannot measure the counter-ion or the assay, and it does not distinguish L from D.

The method is useful after a new crystallisation step, a granulation, or a supplier change that might have altered the solid form. Request the reference diffractogram and the limit of detection before accepting a “match”. A clean diffractogram is supporting evidence, not a replacement for IR, rotation and titration, and a missing pattern does not prove the lot is wrong.

Where substitutions show up

Substitutions and the lines that expose them
SubstitutionWhy it can pass a quick checkSignalTest
HydrochlorideSame lysine entity; the titration still reads lysineChloride near 19%; pH 5–6Chloride; pH
D-lysineSame formula and massRotation of the wrong sign or sizeRotation; chiral HPLC
DL-lysineSame formula and massRotation near zeroRotation; chiral HPLC
Other amino acidSimilar acid–base behaviour and massIR or chromatographic mismatchIR; amino-acid profile
DiluentLowers the titration without a matching impurityAssay low; water or residue may riseTitration; mass balance
WaterThe assay can be corrected to dry matterLoss on drying high; as-is assay lowLoss on drying

The salt is the most plausible substitute: it is a legitimate lysine material with a similar titration. It fails the chloride and pH checks, not the lysine check. D- and DL-lysine keep the formula and the mass and fail the rotation. Another amino acid is exposed by IR and the chromatographic profile, and a diluent by the mass balance. No single assay catches all of them.

Writing identity into the specification

  • “L-lysine free base, CAS 56-87-1, C6H14N2O2, white to off-white powder.”
  • “Identification by IR against a reference and by titration; state the technique and the reference.”
  • “Assay 98.5–101.5% by titration, calculated as the free base; state the as-is or dried basis.”
  • “Specific rotation +25.0° to +27.0° at c=2 in 5 M HCl, with temperature and wavelength.”
  • “Loss on drying ≤0.5%; particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”
  • “No added L-lysine hydrochloride, D-lysine, other amino acids or diluent.”
  • “Chloride reported on request, with the method and the detection limit.”

What to ask the supplier

  1. What IR reference and sample preparation did you use, and can you share the spectrum?
  2. What are the specific rotation and its conditions for this lot?
  3. What is the assay basis, and which titration method was used?
  4. What is the chloride result, or the detection limit if chloride was not detected?
  5. Which lot code ties the certificate, the drum and the retention sample together?

Read together, five answers make an identity file; one assay percentage does not. The catalog specification is on the product hub. The other form is on the hydrochloride page. Release figures and their certificate positions are on the COA page; the grades page sets out the form comparison; the narrow chloride and label question is on the level-four page; methods are in the methods library; the release file is described on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation