02 Form comparison

L-lysine free base or hydrochloride: choosing the form

Technical document 02 · Reviewed 2026-11-20 · L-Lysine

On this page
  1. Why there are two products
  2. The two forms against each other
  3. Water, alkalinity and flow
  4. The dose and the fill
  5. What the specification should say
  6. When the other form is the better fit

There are two L-lysine products, not two strengths of one product. The free base is the amino acid itself, CAS 56-87-1, 146.19 g/mol; the hydrochloride is the salt, CAS 657-27-2, 182.65 g/mol, of which about 80% is lysine and 19.4% is chloride. A label that names L-lysine and a fill that cannot spare 25% extra powder point to the base; a pH 5–6 solution and a crystalline blend point to the salt. The choice belongs before the artwork.

In one line

The base delivers the full lysine mass with no chloride, but it is alkaline and hygroscopic; the salt is easier to handle and adds 25% mass.

Why there are two products

L-lysine has two amino groups, and the hydrochloride is formed by adding one equivalent of hydrochloric acid to the base. That gives a crystalline salt with a counter-ion, a lower pH and a known chloride content. The base has no counter-ion mass, so it delivers more lysine per milligram, but it is more hygroscopic and its solution is alkaline.

The catalog free base is a powder at ≥95% through 80 mesh; a granulated grade can be quoted on request. Mesh is a second decision, separate from the form: it changes flow and dust without changing the molecule. Write both into the specification.

The two forms against each other

L-lysine free base and L-lysine hydrochloride
What changesFree baseHydrochloride
Ingredient nameL-lysineL-lysine hydrochloride
CAS number56-87-1657-27-2
Molecular weight146.19 g/mol182.65 g/mol
Lysine in one gram1.00 g0.800 g
Counter-ionNoneChloride, 19.4% by mass
Solution reactionAlkalinepH 5.0–6.0 at 5%
Water uptakeHigherLower, but still hygroscopic
Assay line98.5–101.5% by titration, as the base98.5–101.5% by titration, dried basis, as the salt

Read the last row before comparing two quotations. A “99%” figure on a base certificate and a “99%” figure on a salt certificate describe two different powders with two different lysine contents. The form and the basis have to match before the percentages can be compared.

Water, alkalinity and flow

Water uptake is the first practical difference. The base is more hygroscopic than the salt, so it needs a tighter seal, a faster weigh-up and a storage record. A base left open in a humid room cakes before the assay moves; the loss on drying is the early signal, and the pack is the control.

The alkaline solution is the second difference. In a drink, an acid will consume part of the base and move the finished pH; in a sealed acidic powder, carbon dioxide taken up by the base can be released and change the pack. The salt is specified at pH 5.0–6.0 for a 5% solution, which is easier to place in a mildly acidic formula but is not neutral either.

Flow is the third. An 80 mesh base powder flows well for capsule filling and blending; a granulated grade reduces dust and changes the dissolution profile. Neither change alters the form or the label.

The dose and the fill

The base delivers lysine one-for-one. The salt delivers 0.800 g of lysine per gram, so the salt weight is 1.25 times the lysine figure. A label that declares 600 mg of lysine needs 600 mg of the base or 750 mg of the hydrochloride. A 600 mg capsule of the salt delivers about 480 mg of lysine.

Lysine declared and the mass to weigh
Lysine on the labelFree baseHydrochloride
300 mg300 mgAbout 375 mg
600 mg600 mgAbout 750 mg
900 mg900 mgAbout 1,125 mg

The extra 25% of salt has to fit the dosage form. A tight capsule may not have the space; a sachet or a beverage powder usually has more. In a tablet, the alkaline base can change the granulation pH and the excipient choice, while a conventional wet granulation is more straightforward with the salt but still needs a moisture limit. Gummies and chews are decided by their water activity and heat process as much as by the form.

What the specification should say

  • “L-lysine free base, CAS 56-87-1, C6H14N2O2; not the hydrochloride.”
  • “Assay 98.5–101.5% by titration, as the free base; state as-is or dried.”
  • “Specific rotation +25.0° to +27.0° at c=2 in 5 M HCl, with temperature and wavelength.”
  • “IR identification, loss on drying ≤0.5%, metals and microbiology as listed.”
  • “Particle size ≥95% through 80 mesh, or the agreed granulated grade.”
  • “Label to name L-lysine and to state whether the quantity is the base or the lysine.”

A specification copied from the hydrochloride is not a base specification. The rotation conditions, the chloride line and the pH range belong to the salt; the base has its own set.

When the other form is the better fit

Do not pick the base for an acidic, sealed powder with no headspace, or for a formula that cannot tolerate an alkaline surface. Do not pick the salt when the label reads “L-lysine” and the dose is declared as lysine, unless the artwork is changed to name the salt. Do not change form to solve flow: mesh and granulation are the right levers, and switching the form creates a labelling problem in place of a hopper problem.

The catalog product is the free base at 80 mesh. The product hub carries the specification; the hydrochloride page covers the other form; the level-four comparison covers chloride, pH and the label in detail; the COA page shows how the lines are reported; the stability page covers water and packaging; the methods library describes the tests; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation