06 Identity & adulteration

How we prove a betaine lot is the anhydrous form

Technical document 06 · Reviewed 2026-11-19 · Betaine

On this page
  1. Four layers of identity
  2. The titration, and its equivalence factor
  3. Infrared: the salt form shows
  4. Water, and the anhydrous claim
  5. Betaine to chloride: the form ratio
  6. XRD for betaine: form evidence, not release identity
  7. Adulteration routes and the tests that see them
  8. How to write the specification
  9. Five questions for the supplier

A betaine lot is the anhydrous form when four independent lines agree: the paper identity, the titration, the infrared spectrum and the water content. The assay alone cannot separate betaine from its hydrochloride, and it cannot see a dilution with a non-basic filler. The file should let a reviewer reach the same conclusion from the numbers and spectra, not the product name.

In one line

Identity is a set of agreeing lines — name, titration, IR and water — not a single assay figure.

Four layers of identity

What each identity layer proves, and what it cannot prove
LayerWhat it provesWhat it misses
Paper identityName, CAS number, formula, sourceA wrong label on a correct-looking drum
TitrationTitratable betaineChloride, neutral diluents
Infrared spectrumThe molecular structure and the salt formMixture components below detection; quantity
Water and chlorideAnhydrous state; hydrochloride absentOther diluents or counter-ions

A certificate can pass the assay and still describe the hydrochloride, because the titration has no chloride channel. A certificate can pass the infrared check and still be wet. A certificate can pass all four and still be diluted with a neutral powder; that is why the specification needs a residue-on-ignition limit for inorganic diluents and, where the risk justifies it, a chromatographic screen for organic ones.

The titration, and its equivalence factor

The identity file uses the release titration, read for its equivalence factor rather than only the percentage. Each millilitre of 0.1 N perchloric acid corresponds to 11.72 mg of C5H11NO2 (117.15 g/mol). The report should give the sample mass, titrant concentration, blank and factor; with those, a second laboratory can reproduce the number.

The calculation has two steps: the titrated mass is converted to betaine using the equivalence factor, then divided by the dry matter to put it on the anhydrous basis. A result calculated as-is against a 97.5–102.5% anhydrous window is not the same test.

The titration measures the carboxylate, not the molecule. It counts any titratable species with a similar equivalent mass and does not see a neutral filler, which is why the file pairs it with IR and a water result.

Infrared: the salt form shows

Infrared spectroscopy reads the functional groups. Betaine anhydrous is an inner salt: the carboxylate is deprotonated, and the spectrum shows carboxylate absorption rather than a carboxylic-acid carbonyl. Betaine hydrochloride is the protonated acid with a chloride counter-ion, so the carbonyl region changes. A reference spectrum run on the same instrument and preparation is the comparison that matters.

An IR match is an identity check, not a purity assay. It confirms that the solid is the anhydrous form and not the hydrochloride, and it can flag a different salt. It cannot tell a 98% powder from a 90% powder when the diluent is IR-transparent. The report should include the spectrum, reference and preparation, not only the word “conforms”.

Water, and the anhydrous claim

The catalog limit is ≤2.0% loss on drying, and the assay is reported on the anhydrous basis, so water is part of the identity file. A lot that passes the assay as-is but carries 3% water is not the anhydrous grade.

The monohydrate is the clearest substitution: it carries about 13.3% water by mass (18.02 ÷ 135.17), far above the 2.0% limit. A monohydrate sold as anhydrous fails loss on drying even when the titration looks normal.

Loss on drying and Karl Fischer answer different questions: loss on drying measures what leaves the sample under the stated conditions, including residual solvent; Karl Fischer measures water specifically. The certificate should name the method; for a hygroscopic powder, handling matters as much as the oven setting.

Betaine to chloride: the form ratio

Betaine anhydrous is an inner salt with no counter-ion; betaine hydrochloride is the 1:1 salt of the same molecule with hydrogen chloride. The ratio separates them. The hydrochloride has a molar mass of 153.61 g/mol, so chloride is 23.1% of the mass and betaine 76.3%; the betaine-to-chloride mass ratio is about 3.3:1.

That gives a cross-check no single assay provides. An anhydrous lot at 97.5–102.5% assay should carry no chloride above the agreed limit; a hydrochloride lot at the same assay must carry about 23% chloride.

XRD for betaine: form evidence, not release identity

Betaine is crystalline, and the anhydrous form, the monohydrate and the hydrochloride each give their own diffraction pattern, so XRD can separate the three in the solid state. It is not the release identity test: IR, titration, chloride and loss on drying answer the same questions with simpler equipment, and a diffractogram proves nothing unless the reference pattern came from the same crystal form.

Two limits matter. XRD sees crystalline phases only, so amorphous diluent and water are invisible, and the pattern of a mixture is read qualitatively rather than as a percentage. Use it when a form claim is disputed or a crystalline excipient is suspected; otherwise the release lines do the work.

Adulteration routes and the tests that see them

Betaine adulterants and the tests that separate them
AdulterantWhat it changesTest that sees it
Betaine hydrochlorideChloride, acidic pH, lower betaine per gramChloride, pH, IR, assay factor
Choline chlorideAnother quaternary ammonium saltHPLC or ion chromatography, IR
Tetramethylammonium chlorideA smaller quaternary saltIon chromatography
Sucrose, dextrose, maltodextrinDilution, water, flowHPLC, loss on drying
Sodium chlorideDilution, chloride, ashChloride, residue on ignition
Betaine monohydrateWaterLoss on drying (about 13.3%)
Other betaine saltsA different counter-ionIon chromatography, IR, titration

The list covers the routes that appear in the market: the wrong salt, a substitute quaternary ammonium compound, a neutral diluent and the hydrated form. Each route has a different blind spot, which is why one test cannot close the file.

How to write the specification

  • “Material: betaine anhydrous, CAS 107-43-7, C5H11NO2; the hydrochloride and the monohydrate are excluded.”
  • “Assay 97.5–102.5% by titration on the anhydrous basis; loss on drying ≤2.0%.”
  • “Identity by IR against a reference spectrum; chloride absent or below the agreed limit.”
  • “Residue on ignition ≤0.1%; pH 5.0–7.0 in 5% solution; ≥95% through 30 mesh.”
  • “Chromatographic purity screen where the risk justifies it; no added diluent.”

The specification should name the form, the basis and the tests that exclude the other forms. “Betaine 98%” does none of those things: it does not say anhydrous, titration or which salt is excluded.

Five questions for the supplier

  1. Which form and CAS number does the certificate describe, and is the assay on the anhydrous basis?
  2. What is the water result, and which method produced it?
  3. Is chloride tested, and at what limit?
  4. Can you send the IR spectrum and the reference it was compared with?
  5. Which chromatographic screen covers other quaternary ammonium compounds and neutral diluents?

Five direct answers, with documents, are worth more than a certificate that says “conforms” on every line. The COA page shows where each result sits on the certificate; the form comparison explains why the hydrochloride is a different ingredient; the anhydrous versus hydrochloride page covers dose and label. The product page carries the catalog specification, and the FTIR note explains the spectrum.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation