Betaine anhydrous vs betaine HCl: dose, pH and the label
The two betaine forms differ in more than the label: betaine anhydrous is the inner salt at 97.5–102.5% by titration and pH 5.0–7.0, while betaine hydrochloride is the chloride salt at about 76% betaine and a pH near 1. A formula written for one form cannot be switched to the other without recalculating the dose and rechecking the pH, the capsule fill and the label.
Betaine anhydrous and betaine HCl are not interchangeable at equal weight: the salt delivers about three-quarters as much betaine and brings a strong acid with it.
Two salts, one betaine
Betaine is trimethylglycine, a zwitterion with a quaternary ammonium group and a carboxylate. In the anhydrous form the molecule is sold as the inner salt, CAS 107-43-7, formula C5H11NO2, molecular mass 117.15 g/mol. In the hydrochloride form one equivalent of hydrochloric acid is added, giving C5H11NO2·HCl, CAS 590-46-5 and a molecular mass of 153.61 g/mol.
The difference is not a grade or a concentration. It is a different chemical on the certificate, a different ingredient on the label and a different number in the capsule. The betaine part is the same; everything around it is not.
The dose conversion
The hydrochloride is 76.3% betaine by mass (117.15 ÷ 153.61). To deliver a target amount of betaine, divide by 0.763, or multiply by 1.311. The table gives the common targets.
| Betaine target | Anhydrous | Hydrochloride |
|---|---|---|
| 500 mg | 500 mg | 655 mg |
| 1 g | 1 g | 1.31 g |
| 2 g | 2 g | 2.62 g |
The conversion changes the fill weight. A capsule that holds 500 mg of the anhydrous powder will not hold 655 mg of the hydrochloride without a change of size, and a stick pack built around 2 g of anhydrous betaine needs 2.62 g of the salt for the same betaine label. The excipients and the overage, if any, are separate decisions.
State the basis on the purchase order and on the formula record. “1,000 mg betaine” and “1,000 mg betaine hydrochloride” are not the same instruction, even though both can produce a label that reads 1,000 mg.
pH, water and the acid load
The anhydrous form gives a 5% solution at pH 5.0–7.0. That is close enough to neutral for a simple capsule or tablet, and it is the reason the anhydrous grade is the usual choice when the betaine is one ingredient among many. The hydrochloride gives a solution near pH 1. The acid is not a contaminant; it is part of the salt, and it arrives in the formula with the betaine.
The anhydrous powder is hygroscopic. It takes water from humid air, and the gain appears in the loss-on-drying result and in caking. The hydrochloride takes up less water at the same humidity, but its acidity can attack acid-sensitive actives and change the taste and the local pH of a powder blend. Neither form should be left open in a production room.
Solubility is high for both, so dissolution is rarely the limit in a capsule or a stick pack. The practical limits are fill weight, flow, taste and the sensitivity of the other ingredients. A form change can solve one of those and create another.
What each form fits
For capsules and tablets, the anhydrous form usually gives the most betaine per unit and the least acid load. A 500 mg capsule can carry 500 mg of betaine as the anhydrous powder; the same capsule carries about 382 mg of betaine as 500 mg of the hydrochloride. If the label target is high and the capsule size is fixed, the anhydrous form is the simpler route.
For powder sticks and drink mixes, the choice is more about taste and the rest of the blend. The hydrochloride's acidity can be useful in a formula built around an acid profile, and it can be wrong in a mild, neutral drink. Test the finished mix, not only the raw powder.
For acid-sensitive actives, the anhydrous form is the default. The hydrochloride's solution near pH 1 can degrade an active that is comfortable at pH 5–7, and the effect may not show up in a raw-material stability study. For effervescent systems, the acid load belongs in the acid–base balance of the formula, not in the inert-carrier column.
What the label can say
In the EU, the ingredient list names the form that is in the product. “Betaine” or “betaine anhydrous” describes the inner salt; “betaine hydrochloride” describes the salt. The two names are not interchangeable, and any novel-food statement that applies sits alongside the ingredient name, not in place of it.
In the US, the Supplement Facts panel states how much of the dietary ingredient is present, and the ingredient list names the source. Where the source is the hydrochloride, the panel should say whether the number is the salt or the betaine. A panel that declares the salt amount and a panel that declares the betaine amount describe different products unless the basis is stated.
In the UK, the retained labelling rules follow the same logic: name the form, declare the amount and keep the claim within the authorised register. “Trimethylglycine” is another name for betaine, not a separate ingredient; use one name consistently across the label, the COA and the specification.
When to choose which
Choose the anhydrous form when the target is the highest betaine mass per capsule or tablet, when the formula needs a near-neutral solution, when the other ingredients are acid-sensitive, or when the customer's specification names betaine anhydrous. Choose the hydrochloride when the purchase order and the label name the salt, when the acid profile is intended and has been tested, and when the customer's formula has been built around that form.
Do not switch forms to fix a flow, taste or stability problem before the mesh, the excipients and the pack have been checked. A form change is a formulation change: it moves the dose, the pH, the capsule fill and the label at once. Run a trial with the new form in the finished matrix, and update the specification and the artwork before the first production order.
The wider comparison is on the form comparison page; the COA page shows what the certificate reports; the water and pack question is on the stability page; the compliance page covers the label rules. The product page lists the catalog grade.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation