03 Stability

Acetyl-L-carnitine is hygroscopic and its ester can hydrolyse

Technical document 03 · Reviewed 2026-11-20 · Acetyl-L-Carnitine

On this page
  1. The dry powder: water is the first problem
  2. The solution: the ester bond is the weak point
  3. What drives degradation
  4. A stability protocol for the pack
  5. Where the formula changes the answer
  6. How the shelf life is set

Acetyl-L-carnitine is hygroscopic as a solid and hydrolyses as an ester in solution. The dry powder needs a sealed, moisture-barrier pack and a cool store; the solution needs a pH and a heat load that keep the ester intact. Shelf life is assigned from data for the exact pack and matrix, not from the certificate.

In one line

The powder fails on water and the ester fails in alkaline solution; the pack and the matrix decide which of the two arrives first.

The dry powder: water is the first problem

The catalog limits loss on drying to ≤1.0%, which is a release gate, not a storage allowance. The hydrochloride picks up water from the air; the powder softens, cakes and bridges, and the as-is assay falls as the water rises. The ester can also hydrolyse slowly in the solid state when water and heat are present, so a wet lot is not only a handling problem.

The pack is the barrier. The 1 kg foil pouch and the 25 kg drum with an inner liner keep water out while they are sealed. An opened pouch folded over is not resealed; the headspace now holds room air, and the powder will equilibrate with it. Keep the original pack closed, use a smaller opaque container for a partial weigh-out, and record the opening date.

Temperature matters through the same route: a warm store raises the rate of both water uptake and hydrolysis. A cool, dry store is the ordinary condition; a hot loading bay or a car in summer is not. The material is not specified here as light-sensitive, and the foil pack covers that question in any case.

The solution: the ester bond is the weak point

Acetyl-L-carnitine is reported stable at neutral to acidic pH and unstable above about pH 9, and the rate rises with temperature. The catalog material is the hydrochloride, so a freshly prepared solution is acidic, which is the friendlier side of that window. An alkaline matrix, a buffer at high pH, or a process that adds heat shifts the balance.

Hydrolysis produces L-carnitine and acetate. The assay of intact ester falls, the free carnitine rises, and the pH can move as acetic acid is released. A beverage or a stick pack made with acetyl-L-carnitine therefore needs a stability study in the matrix, at the process pH and heat load, not only a bulk-powder result. Pasteurisation or hot fill is a heat load that a powder never sees.

Hold time is part of the study. A solution held in a tank for a shift at ambient temperature is a different exposure from one filled immediately; ask for the hold time that was validated, not only the shelf life of the finished pack.

What drives degradation

Factors that move acetyl-L-carnitine during storage
FactorWhat it doesControl
WaterHygroscopic uptake; caking, loss-on-drying rise and as-is assay fallSealed foil or lined drum; dry dose room
HeatAccelerates hydrolysis and water uptakeCool store; control the process temperature
Alkaline pHSplits the ester to carnitine and acetateKeep the matrix acidic to neutral; validate the buffer
TimeHydrolysis accumulates even at a moderate rateAssign the retest period from data
Open packRoom air and humidity enter the headspaceReseal, use the opened pack first, record the date
Matrix water activityCreates a humid microclimate in a stick or capsuleDry the blend; test the finished pack

These factors act together. A warm, humid store with an opened pouch is worse than either condition alone, and an alkaline drink that is also pasteurised combines pH and heat. The useful question is not whether the material is stable, but stable in which pack, at which pH, for how long.

A stability protocol for the pack

Run the study on the pack that will be sold. Long-term storage at 25 °C/60% relative humidity, intermediate storage at 30 °C/65% and accelerated storage at 40 °C/75% cover the warehouse and stress the pack. Test appearance, loss on drying, assay, specific rotation, free carnitine, the pH of a standard solution and microbiology at each point.

Add two arms that a standard solid study misses: an open-pack arm, where the pouch is opened, folded and stored as a customer would, and a solution arm at the target pH and heat load. Those are the two failure modes that matter for this ester. Time points of 0, 3, 6, 12, 24 and 36 months are a practical starting set.

The report should show the individual results and identify the pack and the lot family. A pass statement without numbers does not show a trend, and a trend in free carnitine is the earliest sign that the ester is going.

Where the formula changes the answer

A capsule or tablet starts dry, but the shell and the excipients can move water into the fill; check loss on drying and appearance after storage, not only at release. A stick pack fails at the seal and at the powder's water activity; a pinhole is enough. A liquid combines pH, heat and time, and an alkaline system is the worst case for this ester.

An overage does not repair a pack that lets water in. If the label claim has to hold at end of shelf life, the overage is a label and stability decision, and it must be supported by the matrix data. The ingredient's bulk stability is the starting point, not the answer.

How the shelf life is set

We do not publish one shelf-life number for acetyl-L-carnitine, because the pack, the storage condition and the matrix set it. The assigned retest period belongs on the specification and is supported by the stability file for that pack. After the retest period, re-assay the retained sample before extending use; do not carry a bulk figure across to a repacked container.

The catalog specification is on the acetyl-L-carnitine product page; the release tests are on the COA page; the packs that carry the barrier are described on the MOQ page. The difference from L-carnitine is set out on the level-four page, the parent molecule is on the L-carnitine page, the analytical methods are collected under methods, and the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation