02 Grade comparison

Acetyl-L-carnitine hydrochloride: form, mesh and grade

Technical document 02 · Reviewed 2026-11-20 · Acetyl-L-Carnitine

On this page
  1. Why there is more than one grade
  2. The hydrochloride and the free base
  3. Particle size, flow and water
  4. What the grade does to the fill
  5. What to write into the specification
  6. When another grade is the wrong choice

Acetyl-L-carnitine is supplied as the hydrochloride, as the free base and in more than one particle size, and those are specification choices rather than trade names. The catalog material is the hydrochloride, CAS 5080-50-2, a white to off-white 80-mesh powder; the free base has its own CAS number, molecular weight and label name. The grade decides the carnitine content per gram, the chloride load, the acidity and how the powder runs.

In one line

The grade question is the salt form and the particle: the hydrochloride, the free base and the mesh change the label, the chloride load and the fill weight.

Why there is more than one grade

Acetyl-L-carnitine is an ester of L-carnitine. The hydrochloride is the common commercial form: a freely soluble salt that is easy to weigh and blend. The free base is the same ester without the chloride, and it is a different chemical entity on paper, with a different molecular weight and a different label name. A purchase order that says only “acetyl-L-carnitine” has not chosen between them.

The second axis is physical. The catalog powder is specified at ≥95% through 80 mesh, and a granulated form is available on request. The chemistry does not change with the mesh, but the flow, the dust, the dispersion and the water uptake do. The grade is therefore a form decision and a particle decision, and both belong in the specification before the quotation.

The hydrochloride and the free base

Acetyl-L-carnitine hydrochloride and free base
PropertyHydrochloride (catalog)Free base
CAS number5080-50-23040-38-8
FormulaC9H18ClNO4C9H17NO4
Molecular weight239.70203.24
Chloride14.79% by massNone
Carnitine per gram0.67 g0.79 g
Label nameAcetyl-L-carnitine hydrochlorideAcetyl-L-carnitine
Typical useCapsules, tablets, powder blendsWhere the chloride is not wanted

The carnitine figures are stoichiometry, not certificate results: 161.20 ÷ 239.70 = 0.6725 for the hydrochloride and 161.20 ÷ 203.24 = 0.7931 for the free base. A certificate should still report the assay it measured, because the powder may contain water and the assay has a basis.

The two forms also differ in what the label must say. In the European Union and the United States, the ingredient declaration has to name the form that is in the pack; “acetyl-L-carnitine” does not cover the hydrochloride if the market requires the salt name, and the hydrochloride does not become the free base because the carnitine figure is close. The declaration, the specification and the certificate should use the same name.

Particle size, flow and water

The 80-mesh specification is finer than the 40 mesh common for many amino acids. A finer powder disperses quickly in a blend and gives a uniform-looking capsule fill, but it also carries more surface, so it picks up water faster and generates more dust. Granulation improves flow and reduces dust, at the cost of a slower dissolution step.

The material is hygroscopic. In an open dish it gains water, and in a hopper it can bridge or stick to the dosator. The 80-mesh line is a release specification, not a promise about flow; ask for the bulk density and a flow result if the fill relies on volume. The catalog does not publish a bulk density, so it is a question rather than an assumption.

The hydrochloride solution is acidic. That acidity is part of the grade: in a stick pack or a drink it affects taste and the pH of the matrix, and in a capsule it is less visible but still present if the shell or an excipient is pH-sensitive. The free base removes the chloride but not the ester, so the hydrolysis question remains.

What the grade does to the fill

A label that declares 500 mg of acetyl-L-carnitine hydrochloride is built on 500 mg of the salt; the carnitine delivered is about 336 mg, because the salt is 67.3% carnitine by mass. If the label declares 500 mg of carnitine rather than the ester, the powder weight is different: about 744 mg of the hydrochloride. Those are label arithmetic, not dose advice, and the assay and water content are applied on top.

Capsules and tablets take the solid. A capsule fill is set by the bulk density and the flow of the blend, and a hygroscopic powder needs a low-humidity dose room and a sealed pack. A tablet needs compression behaviour; the catalog does not publish a compactability figure, so run a trial with the actual blend rather than assume a capsule powder will press.

Powder blends and stick packs take the 80-mesh powder because it disperses. The constraint is water activity: a stick pack with a high water activity gives the powder a humid microclimate, and a hygroscopic carrier makes it worse. Granulated material is easier to fill but slower to dissolve; choose it when flow matters more than dispersion.

What to write into the specification

  • “Acetyl-L-carnitine hydrochloride, CAS 5080-50-2, C9H18ClNO4, molecular weight 239.70.”
  • “Assay 98.0–101.0% by HPLC, with the basis stated; loss on drying ≤1.0%.”
  • “Specific rotation −28.0° to −30.0° at c=2 in water; report the conditions.”
  • “Chloride about 14.79% by titration or ion chromatography, where the salt form is to be proved.”
  • “Particle size ≥95% through 80 mesh; granulated on request.”
  • “Heavy metals, microbiology and the pack as listed on the product page.”

We supply the hydrochloride. The free base is a different purchase with a different specification and label, and it should not be substituted without written change control.

When another grade is the wrong choice

Do not choose the hydrochloride when the label names L-carnitine or acetyl-L-carnitine free base; the declared ingredient and the weighed ingredient would differ. Do not choose it for an alkaline matrix where the ester will hydrolyse faster, or for a formula that cannot take the chloride load. The free base is not automatically the answer either: it has its own solubility, pH and stability, and a switch in either direction is a new specification.

A granulated grade is the wrong choice when the application needs fast dissolution in a stick pack; the 80-mesh powder is the practical starting point. A finer mesh is not automatically better, because dust and water uptake rise as the particle shrinks.

The catalog specification is on the acetyl-L-carnitine product page; the release tests are on the COA page; the water and hydrolysis question is followed on the stability page. The difference from L-carnitine is set out on the level-four page, the parent form is on the L-carnitine page, the analytical methods are collected under methods, and the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation