MK-4 is light- and heat-sensitive; the pack sets the shelf life
Menaquinone-4 is a light-sensitive, low-melting solid. The isolated powder is most stable in a sealed, opaque pack at a cool temperature; an oil solution and an emulsion add oxidation and heat to the list. Shelf life is assigned from data for the exact pack and matrix, not from the certificate.
Menaquinone-4 is a low-melting, light-sensitive solid, so the pack and the storage temperature decide more of the shelf life than the molecule does.
The powder in the sealed pack
The catalog sets loss on drying at or below 0.5%, which is a release gate rather than a storage allowance. A crystalline solid with that little water picks up moisture slowly, but the pack still has to keep it out: an opened pouch in a humid room will gain water at the surface, and the as-is assay falls as the moisture rises. The standard packs are a 1 kg foil pouch and a 25 kg fiber drum with a food-grade liner; both block light while they stay closed, and both fail at the seal or the liner.
Heat is the more specific problem. The isolated material has a low melting range for a crystalline solid, reported around 35–38 °C, so a drum left in a warm loading bay or a pouch stored above a heater can soften, gloss over or cake even when the moisture is low. A cool, dry, dark store is the practical instruction, and cold storage is common for the isolated material; let the pack equilibrate to room temperature before opening so that condensation does not form on the powder. A clear jar on a bench is an exposure, not a storage container.
Oil, softgel and emulsion
MK-4 is practically insoluble in water and soluble in fats and organic solvents, so an oil solution is a natural format and a softgel is a natural pack. The oil introduces its own stability file: the carrier oil can oxidise, its peroxides can attack the menaquinone, and light passes through many oils and through a clear softgel shell. Specify the oil, its peroxide value and any antioxidant, and use an opaque shell with a controlled headspace.
The low melting point also changes the process. A warm oil dissolves the material readily, and the same solution can throw crystals on cooling if the concentration is close to saturation; a fill that is clear at 40 °C is not necessarily clear at 20 °C. Check the concentration at the temperature the fill will actually see, and check the softgel seam and fill appearance after storage.
An emulsion is the least stable format. Water, oil, light, oxygen, heat and pH act at once, and a pasteurisation or hot-fill step adds a heat load the bulk powder never meets. If a drink is unavoidable, protect it from light, control the dissolved oxygen and the pH, and validate the hold time in the finished matrix rather than on the bulk powder.
What drives the loss
| Factor | What it does | Control |
|---|---|---|
| Light | Photodegradation; colour and assay change | Opaque foil or drum liner; dark store |
| Heat | Softens and cakes the powder; accelerates oxidation | Store below 25 °C; cool process; short heat exposure |
| Oxygen | Oxidises the quinone ring, especially in oil | Sealed pack; low headspace; declared antioxidant |
| Moisture | Raises loss on drying and lowers the as-is assay | Sealed pack; dry store; reseal after opening |
| Alkali and metals | Attack the quinone in an emulsion or a wet matrix | Check pH; avoid iron and copper contact |
The routes reinforce one another. A store that is warm, bright and humid at once is worse than three separate problems, and an oil in clear glass combines light and oxygen in the same container. The question worth asking is not whether MK-4 is stable, but for how long in this pack, at this temperature.
A stability protocol for the ingredient
A protocol is useful when it fixes the pack, the condition, the time points, the tests and the acceptance limits before the first sample is charged. A warehouse is covered by a long-term condition of 25 °C and 60% relative humidity plus an intermediate condition of 30 °C and 65% relative humidity; an accelerated run at 40 °C and 75% relative humidity puts pressure on the pack. A light arm on the ICH Q1B design covers what a dark incubator cannot.
Test assay, related substances including menadione, loss on drying, appearance and microbiology at each point, and add the melting range when the solid form matters. In an oil, add the peroxide value and the fill appearance; in an emulsion, add the droplet size and the pH. The report should carry the individual figures rather than a pass line, and name the pack and the lot family.
The summary should describe the pack you are actually buying. The drum and the pouch differ in headspace and in how often they are opened, and a softgel is a different subject again.
The finished formula changes the answer
Capsules and tablets keep water activity low, but the excipients can still pass moisture, and a fill that contains a low-melting material can soften if the product is stored warm. Check the appearance of the fill at release and after storage, not only the assay. An opaque shell or an opaque film coating is a simple barrier that is easy to specify and easy to audit; a clear capsule gives light free access to the powder.
A gummy adds the heat of cooking and a water activity that a capsule does not have. Adding the MK-4 late in the process reduces the heat exposure, but the finished matrix still has to be tested. An overage is a label and stability decision; it does not repair a pack that lets light or moisture in.
How the shelf life is set
No single shelf-life number applies to MK-4, because the pack, the temperature and the matrix set it. The assigned retest period belongs on the specification, with the stability file for that pack behind it. Without the pack, the condition and the test panel, a number is an assertion rather than a shelf life.
When the retest period ends, re-test the retained sample before extending the date. An extension by assumption, or a bulk figure applied to a repacked container, is not supported. Once a 1 kg pouch is opened, the remainder sees a different environment; split it into smaller opaque units for a long campaign and reseal it properly.
Pack options and the specification are on the product page. The COA page lists the release tests and the MOQ page the ordering unit; the assay is explained in the methods library and the release workflow on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation