06 Identity & adulteration

How we prove a vitamin D3 oil lot is cholecalciferol

Technical document 06 · Reviewed 2026-11-20 · Vitamin D3 Oil

On this page
  1. The identity layers
  2. The IU ratio and the mass balance
  3. X-ray diffraction: what it can and cannot do here
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Six questions for the supplier

A vitamin D3 oil lot is cholecalciferol when the documents, the HPLC retention and UV spectrum, the potency arithmetic and the carrier record agree. At 1.0 MIU/g the cholecalciferol is about 2.5% of the oil, so the identity evidence has to come from the chromatogram and the mass balance, not from the colour. The oil is a solution, and the carrier is part of the identity file.

In one line

A D3 oil is identified when the chromatogram, the UV spectrum and the IU arithmetic agree, and when the carrier is on the record.

The identity layers

Naming the right material on paper does not prove that the material is in the bottle. Each layer asks a different question and needs evidence of its own. An answer that stops at the first layer has described a document, not a liquid.

Five checks that together identify a vitamin D3 oil
LayerQuestionEvidenceWhat it proves
DocumentIs the form and CAS named?Cholecalciferol, CAS 67-97-0, C27H44OPaperwork only
ChromatographyIs the peak cholecalciferol?HPLC retention against a standard, with D2 separatedThe molecule
SpectrumIs the ultraviolet profile right?UV maxima and absorbance ratiosThe chromophore
Mass balanceDoes the IU/g match the mass?IU/g ÷ 40 = µg/g; compare with HPLCThe concentration
CarrierWhat carries the vitamin?Carrier name, fatty-acid profile, allergen statementThe full composition

The IU ratio and the mass balance

One microgram of cholecalciferol is 40 IU. The catalog oil at 1.0 MIU/g therefore contains 25,000 µg/g, which is 25 mg/g or 2.5% by mass; at 1.1 MIU/g it contains 27,500 µg/g, or 2.75%. Those figures are fixed by the definition of the IU, not by the supplier, and they are the arithmetic that ties the label to the certificate.

The check runs both ways. Take the HPLC result in micrograms per gram and multiply by 40 to get IU/g; take the IU/g on the certificate and divide by 40 to get micrograms per gram. If the two do not agree, one of the numbers is wrong, and the certificate should show the conversion so the reader can repeat it.

The carrier-to-vitamin ratio follows from the same figures: at 2.5%, there are about 39 parts of oil for every part of cholecalciferol. That ratio is why a small potency error is easy to make in a large batch and why the carrier record matters. It is also why a D2 substitution can pass a careless potency check while the retention time and the spectrum give it away.

X-ray diffraction: what it can and cannot do here

X-ray diffraction asks about the solid state: whether the material is crystalline and whether the pattern fits a reference. The oil is a liquid solution, so XRD is not a release test for it and a certificate that reports “XRD conforms” for an oil has added little. The technique belongs to the crystalline standard, to the spray-dried powder and to the carrier when a solid form is in question.

XRD is still useful in a dispute. If a bottle throws a precipitate, isolate it and identify the solid; if the powder on carrier is the form being bought, the pattern can separate a crystalline carrier from an amorphous one. A match statement needs the reference pattern and the detection limit before it can be read.

For the oil, the stronger evidence is HPLC with UV detection, the potency arithmetic and the carrier profile. The XRD method note explains what the pattern proves and what it does not.

What adulteration looks like

Common vitamin D3 oil substitutions and the signals
AdulterantWhat it doesSignalTest
Carrier dilutionLowers IU/g; keeps the colourPotency below the range; mass balance offHPLC potency, IU arithmetic
Vitamin D2Cheaper source; similar colourDifferent retention; different UV spectrumHPLC/UV, D2 screen
Under-potencyDeclared IU/g not deliveredAssay short of the labelHPLC against a standard
Oxidised carrierRancid oil; peroxide highPeroxide value above the limit; odourPeroxide value, fatty-acid profile
Undeclared carrierAllergen or label mismatchFatty-acid profile differs from the declared oilGC fatty-acid profile, allergen review

Of the signals available, colour is the easiest to fake: a pale yellow oil is easy to match with a different carrier. The stronger signals are the retention time, the ultraviolet spectrum, the IU arithmetic and the peroxide value. When appearance and potency are reported without identity, the substitution most likely to occur has gone untested.

How to write the identity into the specification

  • “Cholecalciferol oil, CAS 67-97-0, C27H44O, 1.0–1.1 MIU/g by HPLC.”
  • “Identification by HPLC retention against a cholecalciferol standard and by UV spectrum; state the wavelength.”
  • “Potency in IU/g with the micrograms-per-gram equivalent; the conversion factor is 40 IU per microgram.”
  • “Carrier oil named; antioxidant package named; peroxide value ≤10.0 meq O₂/kg.”
  • “A vitamin D2 screen where the form or the source is in question.”
  • “Heavy metals and microbiology as listed; destination market confirmed before the order.”

Six questions for the supplier

  1. Which carrier oil is this lot, and is it named on the certificate?
  2. What is the IU/g, and what is the equivalent in micrograms per gram?
  3. Will you release the chromatogram and the UV spectrum, not just the potency number?
  4. What is the peroxide value, and which antioxidant package is present?
  5. Has the lot been screened for vitamin D2?
  6. In a dispute, would you join a re-test on the retain sample?

Answers to those six questions are an identity file in practice. A single potency figure is not. For the catalog figures, start at the product page. The COA page maps each certificate line; the grades page compares the forms; the oil-versus-powder page follows the carrier and label; the HPLC method note explains the separation; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation