06 Identity & adulteration

How we prove a vitamin A lot is the acetate

Technical document 06 · Reviewed 2026-11-19 · Vitamin A

On this page
  1. The four layers of identity
  2. The IU-to-mass ratio as a check
  3. Why a diffraction scan is not the test here
  4. What substitution looks like
  5. Writing a specification that can be proved
  6. Five questions for the supplier

Four kinds of evidence have to line up before a powder can be called retinyl acetate: the paper trail, the chromatogram, the fatty acid released by hydrolysis, and the mass balance. This powder is only about 17% ester, so colour and a single assay value cannot establish identity. The carrier is the rest of the evidence, and the certificate has to describe it.

In one line

At 500,000 IU/g the ester is only about 17% of the powder, so identity needs the chromatogram, the hydrolysis products and the mass balance to agree.

The four layers of identity

Four identity layers, what each one proves, and its blind spot
LayerEvidenceWhat it provesWhat it does not prove
DocumentaryName, CAS 127-47-9, formula C22H32O2, COA, lot code, specificationThe pack and the file share a lot codeThat the powder is the named ester
ChromatographicRetention time against a retinyl acetate standard, co-injection, diode-array spectrumThe peak matches the acetate standardThe carrier, the IU/g or the ester mass
HydrolyticSaponification, then identification of the fatty acid by GCThe ester carries acetate, not palmitateThe IU/g or the carrier proportion
Mass balanceIU/g converted to µg RE/g, compared with the ester mass and the carrierThe dilution matches the declared gradeWhich ester the molecule is

The HPLC should run a retinyl acetate standard on the same column and mobile phase, co-inject the sample, and compare the diode-array spectrum around 325 nm. A retention time without the standard and the wavelength is a number, not an identification.

Paper can be truthful and still describe another lot. A single peak can be the wrong ester if the standard was wrong. A correct acetate peak can sit in a powder whose carrier is not the one declared. The four layers have to agree; any one of them on its own is not identity.

The IU-to-mass ratio as a check

The IU is a unit of activity, not a mass. One microgram of retinol is defined as 3.33 IU, so 500,000 IU/g is 150,000 µg of retinol equivalent per gram, or 150 mg/g. Pure retinyl acetate is about 2.9 million IU/g, which means the 500,000 IU/g grade contains about 17% ester by mass. The rest is the gelatin, sucrose and starch matrix, moisture and minor solids.

That ratio is a useful identity check because the two common esters sit at different masses for the same IU figure. At 500,000 IU/g, retinyl acetate is about 17% of the powder, while retinyl palmitate would be about 27%. If a lot is declared as the acetate but the mass balance points to the palmitate range, the discrepancy needs an explanation before the lot is accepted. The check does not replace the chromatogram or the hydrolysis test; it tells the reviewer where to look.

The figures need a common basis. With loss on drying allowed up to 5.0%, a dried-basis assay reads higher than the as-sold figure. Compare the IU/g, the moisture and the ester mass on one basis, or the ratio will drift for a reason that has nothing to do with identity.

Why a diffraction scan is not the test here

X-ray diffraction is the identity workhorse for crystalline mineral chelates, where the lattice gives a fingerprint. It is the wrong tool for this powder. The spray-dried matrix is largely amorphous, and the vitamin at roughly 17% may not produce a useful pattern; crystalline sucrose or starch can dominate the scan and tell the reviewer about the carrier rather than the ester. A clean diffractogram would not prove retinyl acetate, and a noisy one would not disprove it.

Diffraction still has a place as a screen for crystalline adulterants or as a check on the carrier, but it belongs beside the chromatographic and hydrolytic evidence, not in place of them. The identity tests that matter for this product are the HPLC retention time against a matching standard and the fatty acid released on hydrolysis.

What substitution looks like

Common substitutions and the tests that expose them
SubstitutionWhat it changesHow to detect it
The wrong ester (palmitate for acetate)Higher mass per IU, different label nameHPLC against both standards; hydrolysis and GC of the fatty acid
Beta-caroteneDifferent molecule and chromophore; no retinol on hydrolysisHPLC with diode-array detection at the carotene wavelength; hydrolysis
Low potency or carrier dilutionIU/g below the declared gradeAssay plus mass balance against the ester and carrier
Free retinol or cis isomersOxidation marker; cis forms have lower activityChromatographic profile, retinol peak, stability data
Carrier substitutionAllergen, label and flow behaviour changeCarrier declaration, protein and carbohydrate tests, flow trial

Beta-carotene is the substitution that a single-wavelength assay misses most easily, because its absorption sits away from the retinoid maximum. A method that looks only at the retinoid wavelength can miss it entirely. The certificate should name the wavelength and the standard, and an identity screen should cover the carotene region as well.

Writing a specification that can be proved

A line that says “vitamin A ≥500,000 IU/g” is a potency target, not an identity specification. A usable line names retinyl acetate and its CAS, states the IU/g and the HPLC method, states whether the result is as sold or on the dried basis, names the carrier and the gelatin source, and adds loss on drying, mesh, heavy metals and micro. If an antioxidant is present, it belongs in the line too.

The specification should also state the overage policy and the acceptance tolerance, because those decide whether a lot above the floor is released as compliant. The batch COA confirms the lot against that version; a certificate issued against an older version is a different document. Keep the version number on the certificate and in the purchase order.

Five questions for the supplier

  1. Which ester is this lot, and which reference standard was used for the HPLC identity?
  2. Was the sample saponified before the assay, and what fatty acid did the hydrolysis release?
  3. What are the carrier proportions and the gelatin source, and is the gelatin fish, bovine or porcine?
  4. On which IU basis was this lot released, with what overage policy and against which specification version?
  5. Can you send the chromatogram, the hydrolysis data and a retained sample with the same lot code?

Check the five answers against the certificate, the pack label and the retained sample. The vitamin A product page carries the catalog specification; the COA page explains the assay lines; the acetate versus palmitate page compares the two esters; and the compliance page lists the file. The HPLC method note and the ICP-MS method note describe the instruments, and the quality page covers release and retention.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation