Riboflavin 5-phosphate vs riboflavin: solubility, assay and the label
Riboflavin 5-phosphate is riboflavin with a phosphate group on the ribitol side chain. The group makes the molecule far more soluble in water and raises its molecular weight from 376.37 to 456.34, so 1 mg of the phosphate delivers about 0.825 mg of riboflavin. The two are different label ingredients even though they declare the same nutrient.
The phosphate group adds solubility and mass: 1 mg of riboflavin 5-phosphate delivers about 0.825 mg of riboflavin, and the label has to say which figure it declares.
Two molecules, one nutrient
Riboflavin is the parent molecule. Riboflavin 5-phosphate, also called flavin mononucleotide or FMN, carries a phosphate ester at the 5' position of the ribitol chain. The flavin ring is unchanged; the phosphate is the difference. That is why the two share the yellow colour and the UV spectrum but not the solubility or the molecular weight.
The CAS numbers are separate: 83-88-5 for riboflavin, 146-17-8 for the free acid, 130-40-5 for the sodium salt. A specification that names one does not cover the other. The nutrient on the label is riboflavin in both cases; the ingredient statement names the source.
The phosphate form is not a more concentrated riboflavin. It is heavier, so the same mass carries less riboflavin. The direction of the conversion matters: multiply the phosphate mass by 0.825 to get riboflavin, not the other way round.
Solubility: the practical reason for the phosphate
Riboflavin dissolves only sparingly, about 0.07 g/L at room temperature. That limits it in beverages and in any liquid concentrate: it can be suspended, but not dissolved at a useful concentration. The phosphate group makes the molecule soluble; the catalog describes the free acid as soluble in water, with a yellow, slightly acidic solution.
The sodium salt is more soluble again. The USP/FCC description gives about 1 g in 30 mL of water. That is why the sodium salt is the common choice for liquid formats and why the free acid is often used where the sodium load or the market entry points that way.
Solubility is not the same as stability. The solution is photolabile and the phosphate ester can hydrolyse; a dissolved form is the least stable format. The formulation has to protect the solution, not only dissolve it.
Assay: the percentage needs a basis and a molecule
The catalog minimum is ≥95.0% by HPLC. A percentage without a basis is not a specification. The loss on drying can be up to 8.0%, so the as-is and dried figures can differ substantially. At 95.0% as-is and 6.0% moisture, the dried basis is 101.1%; at 95.0% dried and the same moisture, the as-is figure is 89.3%.
The figure also has to say which molecule it is calculated as. 95.0% as riboflavin 5-phosphate is 78.4% riboflavin equivalent. A certificate that reports 95.0% “riboflavin” on a phosphate lot has either converted the number or described a different material. The two cannot both be right.
The specification should fix three things: the form, the basis and the molecule. The certificate should print all three next to the result. Without them, two suppliers can agree on “95%” and ship different powders.
The conversion to the label
The factor from the free acid to riboflavin is 376.37 ÷ 456.34 = 0.8248. The factor from the anhydrous sodium salt is 376.37 ÷ 478.33 = 0.7868; the dihydrate is 376.37 ÷ 514.36 = 0.7317. Use the factor for the form on the certificate, not a generic one.
A label that declares 1.4 mg riboflavin, the EU NRV, needs 1.70 mg of the free acid or 1.78 mg of the anhydrous sodium salt. A 10 mg free-acid dose delivers 8.25 mg riboflavin. The US Daily Value is 1.3 mg; the same arithmetic applies. None of these figures is a recommendation.
Apply the moisture first, then the molecular-weight factor, then the label. A 95.0% assay on the dried basis at 8.0% moisture is 87.4% as-is; the label arithmetic starts from the as-is mass. Missing the moisture step overstates the riboflavin by the moisture content.
Stability follows the form
Both molecules are photolabile, and both need a light-resistant, moisture-barrier pack. The phosphate is more hygroscopic than riboflavin; the catalog allows up to 8.0% loss on drying, against 1.5% for the riboflavin record. An opened pouch takes moisture, and the as-is assay falls.
In solution, the phosphate ester can hydrolyse back to riboflavin, and light degrades the flavin at every pH. The solution is most stable near neutral pH; acid conditions speed hydrolysis. A phosphate in a beverage is not automatically more stable than riboflavin; it is more soluble, and the matrix decides the rest.
Neither form should be called stable without the pack, the matrix and the time. The stability page sets out the protocol.
What the label has to say
In the EU, as of this review, the food-supplement Annex I (Directive 2002/46/EC) names riboflavin and riboflavin-5'-phosphate, sodium. The free acid is not the named sodium form. The label must match the form the market file covers, and the nutrient declaration is riboflavin in mg and %NRV; the ingredient list names the source.
In the US, the Supplement Facts panel declares riboflavin, and the ingredient statement names the phosphate. The Daily Value is 1.3 mg. Structure/function language is reviewed separately, with substantiation and the DSHEA disclaimer; no disease claim is open.
Write the form into the label and the specification, not only into the purchase order. A label that says “riboflavin” while the batch is a phosphate is not wrong about the nutrient, but it is incomplete about the source. A label that says “riboflavin 5-phosphate” while the market file covers only the sodium salt is a different problem.
When to choose which
Choose riboflavin when the formula is a solid with low water activity, when the label calls for plain riboflavin, or when the analytical method and the market file are built around it. It is the simpler ingredient: one molecule, no phosphate ester to hydrolyse, and a lower moisture limit.
Choose riboflavin 5-phosphate when the formula needs dissolved riboflavin at a concentration plain riboflavin cannot reach, or when the label and the market file name the phosphate. Choose the sodium salt when the file names the sodium salt or when the highest solubility is needed; the sodium load and the conversion change.
Switching in either direction needs a new specification, a new certificate, a new conversion and a label check. The phosphate group is not a unit conversion applied at the balance. The product hub carries the catalog specification; the grades page places this comparison in the wider range; the riboflavin page covers the parent form; the compliance page covers the market entries; the methods library describes the assay; the quality page covers release.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation