01 COA & batch testing

What the COA for riboflavin 5-phosphate actually contains

Technical document 01 · Reviewed 2026-11-20 · Riboflavin 5-Phosphate

On this page
  1. Reading the release panel
  2. The percentage needs a form and a basis
  3. Limit, result and the difference
  4. What changes from lot to lot
  5. When an outside test is worth ordering
  6. What to put beside two quotations

The certificate for a riboflavin 5-phosphate lot has to settle three things before the assay number means anything: which form was made, what the percentage is calculated on, and how much water the powder carries. The release panel is appearance, HPLC and UV identity, HPLC assay, loss on drying, pH, heavy metals, microbiology and particle size. The catalog sets the gates; the lot certificate reports the measured results.

In one line

The assay needs three anchors: the form on the certificate, the basis of the percentage, and the loss on drying that connects the two.

Reading the release panel

Start with the identification line. HPLC retention and the UV spectrum should match a flavin reference, and the method should separate riboflavin 5-phosphate from plain riboflavin and from the diphosphate. A certificate that says only “HPLC conforms” has not shown the separation.

Then read the assay with the form and the moisture. The table lists the catalog gates; a lot certificate repeats them as limits and adds a measured result for each.

Identity, assay, moisture and contaminants · riboflavin 5-phosphate
ParameterMethodRelease limit
AppearanceVisualYellow to orange-yellow powder
IdentificationHPLC retention and UV spectrumConforms to the reference
AssayHPLC with UV detection≥95.0%, basis and molecule stated
Loss on dryingGravimetric≤8.0%
pH (1% solution)Potentiometric5.0–6.5
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

Appearance and pH are supporting lines. Yellow to orange-yellow is shared by the free acid, the sodium salt and a blend, so colour cannot carry identity. The pH of a 1% solution is a form-sensitive check, but it does not replace phosphorus or sodium.

The percentage needs a form and a basis

Riboflavin 5-phosphate can be reported as the phosphate or as riboflavin equivalent. It can be reported as-is or on the dried basis. Those are two independent choices, and the certificate should name both.

The arithmetic is not small. At 95.0% as-is with 6.0% moisture, the dried basis is 101.1%; at 95.0% dried with the same moisture, the as-is figure is 89.3%. At the 8.0% moisture limit, 95.0% dried is 87.4% as-is. The assay and the loss on drying belong in adjacent columns, not at opposite ends of the page.

The molecule matters too. 95.0% as riboflavin 5-phosphate is about 78.4% riboflavin equivalent. A certificate that reports 95.0% riboflavin for a phosphate lot has either converted the figure or described a different material; 95% as the phosphate and 95% as riboflavin cannot both describe the same powder. The specification should state the form, the basis and the molecule before the first lot is released.

Limit, result and the difference

Each line needs a limit and a measured result. A result column that repeats the limit is not a result; it is the gate copied into the wrong column. The table shows what belongs in each.

What the result column should contain
ParameterRelease limitResult column
Assay≥95.0% by HPLC, basis statedThe measured percentage, the basis and the method
Loss on drying≤8.0%A measured percentage
pH5.0–6.5The measured pH and the concentration used
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 80 meshThe measured percentage through the sieve

Microbiology needs a count plus an absence statement. Heavy metals need a figure per element, not a sum. Assay needs the measured percentage, the basis and the method. “Passes specification” is the conclusion; the numbers are the evidence.

What changes from lot to lot

Phosphorylation is the main batch-to-batch variable. The total assay can sit inside the window while the free riboflavin and diphosphate fractions move. The EU additive specification for the sodium salt (Regulation (EU) No 231/2012) puts limits on both; check the current text. If the buyer needs that profile, ask for the HPLC peak areas, not only the assay percentage.

Moisture follows the drying step and the seal. Colour follows light and heat. Particle size follows the mill; 80 mesh is a finishing line, not a chemical one. The lot code should match the pouch, the drum and the retained sample.

Read the lots as a series. A falling assay with a rising loss on drying is a storage signal. A new peak in the chromatogram is a process signal.

When an outside test is worth ordering

Order an outside test for a new source, a first shipment into a regulated market, a disputed form, or a label that names a grade the certificate does not support. The panel should separate the forms: HPLC with a photodiode array for the flavin and the phosphorylation profile, phosphorus by ICP-OES, sodium by ICP-OES, loss on drying, pH, ICP-MS for metals and the microbiological set.

Phosphorus near 6.8% on the dried basis fits the mono-phosphate; sodium near 4.8% points to the sodium salt. Ask for the detection limit with every “not detected”. The sample tested should be the retained sample, and the report should identify the lot.

When a result is contested, send the referee the retained sample, the supplier's certificate and the agreed specification, and frame the request around the tests that tell the free acid from the sodium salt — not another run of the same assay.

What to put beside two quotations

Compare the form and CAS number; the assay, its basis and the molecule; phosphorus and sodium; loss on drying; pH; and particle size. A match on “95%” with a different form or basis is not a match.

Then compare traceability: manufacturer, phosphorylation route, drying and milling steps, specification revision. The catalog specification is on the riboflavin 5-phosphate product page; the parent nutrient is on the Vitamin B2 page. The tests that separate the forms are on the identity page; the market route is on the compliance page; the HPLC method is in the methods library; release is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation