06 Identity & adulteration

How we prove a lot is methylcobalamin

Technical document 06 · Reviewed 2026-11-20 · Methylcobalamin

On this page
  1. The four identity layers
  2. HPLC and UV-Vis: proving the methyl form
  3. The ratios that carry the identity
  4. X-ray diffraction: the solid-state check
  5. What adulteration looks like
  6. How to write the identity into the specification
  7. Questions to put to the supplier

A methylcobalamin lot is the methyl form when four lines agree: the document names the form and CAS number, HPLC retention against a methylcobalamin standard and the UV-Vis spectrum match, the cobalamin profile shows no other form above its limit, and the assay and moisture close the mass balance. An assay expressed only as vitamin B12 cannot separate methylcobalamin from cyanocobalamin, because both are cobalamins with a similar response.

In one line

The methyl ligand is the identity: retention and the spectrum at about 267, 342 and 522 nm separate it from cyanocobalamin, and the cobalamin profile shows what else is in the peak.

The four identity layers

Paperwork can name methylcobalamin correctly while saying nothing about the solid in the drum. Each layer in the table asks a different question, and the answer to one does not cover the next. A supplier who stops at the first layer has described a label, not a lot.

Four layers of methylcobalamin identity
LayerQuestionTestWhat it proves
DocumentIs the form named?Name, CAS number, formulaPaperwork only
ChromatographyIs the cobalamin methylcobalamin?HPLC retention against a methyl standard plus UV-Vis spectrumThe ligand and the corrin ring
ProfileWhat else is in the peak?HPLC for cyanocobalamin, hydroxocobalamin and other cobalaminsPurity of the form
Mass balanceIs it diluted?Assay, loss on drying, impuritiesConsistency of the numbers

HPLC and UV-Vis: proving the methyl form

The method should name the column, the mobile phase, the wavelength, the solvent and the reference standard. Identity is retention time plus spectrum. A single peak at the right time can be another cobalamin or a degraded standard, so the spectrum is the second dimension rather than a decoration. Methylcobalamin in neutral solution shows maxima near 267, 342 and 522 nm; cyanocobalamin shows maxima near 361 and 550 nm. The gap between those sets is wide enough to read, provided the method uses the right standard and the right solvent.

Use a methylcobalamin reference standard for both identity and assay. Running a methyl sample against a cyanocobalamin standard with an assumed response factor produces a number that looks plausible and describes a different molecule. The standard should be traceable, within its expiry and stored as the certificate directs; a degraded standard changes the retention and the spectrum at the same time.

The ratios that carry the identity

Two ratios do the work. The first is the absorbance ratio at the three maxima. The method should state the ratios it expects, because the spectrum is pH-dependent: in dilute acid the maxima shift to about 264, 304 and 462 nm, so a spectrum measured in the wrong solvent will not match a neutral-solution reference. The second is the chromatographic ratio of the methylcobalamin peak area to the total cobalamin area. The specification should set a limit for each named cobalamin rather than one general purity figure, so that a cyanocobalamin impurity and a hydroxocobalamin impurity are both visible.

Cobalt is a supporting figure, not the deciding one. The methyl form is about 4.38% cobalt by mass and cyanocobalamin about 4.35%; the difference is too small to separate the two forms on a cobalt result. A cobalt figure near the theoretical value confirms that the material is a cobalamin and helps catch a dilution, but the ligand is proved by the chromatogram and the spectrum.

X-ray diffraction: the solid-state check

X-ray diffraction answers a different question: is the solid crystalline, and does its pattern match a reference? Methylcobalamin is supplied as a crystalline powder, so a pattern is meaningful; it can distinguish the crystal from an amorphous trituration or a lyophilised powder, and it can compare lots from two sources. On a diluted grade the carrier dominates the pattern, which is itself useful evidence of what was added.

XRD is not a purity assay and it does not identify the ligand. It is not a routine release test for this product, and a certificate that reports only “XRD conforms” without the pattern or the reference has added little. Ask for the reference pattern and the detection limit before reading a match statement. For a disputed lot, XRD plus HPLC/UV plus the cobalamin profile is stronger than any one of them.

What adulteration looks like

Common methylcobalamin substitutions and the signals
AdulterantWhat it doesSignalTest
CyanocobalaminThe other common B12 form; similar colour and assay responseRetention and spectrum differ; cyano peak presentHPLC/UV against a methyl standard
HydroxocobalaminLight-degradation product; red, so colour still passesExtra peak; spectrum shiftHPLC profile, UV-Vis
Dilution on a carrierLowers the assay; adds a carrierAssay low; loss on drying and ash moveMass balance, carrier identification
DyeMatches the dark red colour, not the spectrumColour without a UV matchUV-Vis, HPLC
MoistureRaises loss on drying; lowers the as-is assayLOD high; anhydrous assay normalLoss on drying

Colour is the weakest signal, because the molecule and its main degradation product are both red and a dye can reproduce the shade. The stronger signals are the retention time, the spectrum and the cobalamin ratio. A certificate that reports appearance and assay but not identity has left the most likely substitution untested.

How to write the identity into the specification

  • “Methylcobalamin, CAS 13422-55-4, C63H91CoN13O14P.”
  • “Assay 98.0–101.0% by HPLC against a methylcobalamin reference standard; state the basis.”
  • “Identification by HPLC retention and UV-Vis spectrum; report the maxima and the absorbance ratios.”
  • “Cobalamin profile: limits for cyanocobalamin and hydroxocobalamin, each reported separately.”
  • “Loss on drying ≤10.0%; heavy metals and microbiology as listed.”
  • “Particle size ≥95% through 80 mesh; pack in a light-resistant, moisture-barrier container.”
  • “The destination market, the intended use and the form are agreed in writing before release.”

Questions to put to the supplier

  1. What is the form and CAS number printed on this lot's certificate?
  2. Can you provide the HPLC chromatogram and the full UV-Vis spectrum, not only the assay percentage?
  3. Which reference standard was used, and in which solvent was the spectrum measured?
  4. What are the cyanocobalamin and hydroxocobalamin results for this lot?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

The five answers together make an identity file; any one alone leaves a gap. The product hub carries the catalog specification, the COA page shows where each result sits, the grades page compares the physical forms, the level-four comparison covers the label and stability consequences, the cyanocobalamin page covers the other form, the HPLC method note explains the separation, and the quality page describes release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation