01 COA & batch testing

What the COA for methylcobalamin actually contains

Technical document 01 · Reviewed 2026-11-20 · Methylcobalamin

On this page
  1. The certificate as a test report
  2. Assay basis, water and the identity standard
  3. Release limit versus batch result
  4. What moves between batches
  5. When an outside test is worth ordering
  6. What to compare between suppliers

A methylcobalamin certificate covers appearance, identity by HPLC with a UV-Vis spectrum, assay, loss on drying, heavy metals, microbiology and particle size. Read it as a set of measurements rather than a verdict: every parameter needs its method, its limit and the figure the laboratory actually obtained. The table below gives the catalog specification; the lot certificate is where the results sit against it.

In one line

The assay is only meaningful with its basis: a methylcobalamin figure beside its loss on drying, and an HPLC/UV identity that distinguishes the methyl form from the other cobalamins.

The certificate as a test report

A certificate is auditable when every line answers three questions: what was measured, by which method, and against which limit. A row that says only “conforms” asks the reader to trust a conclusion without the evidence behind it. For methylcobalamin the identity lines carry more weight than usual, because a cyanocobalamin or hydroxocobalamin lot can produce a plausible assay if the number is expressed simply as vitamin B12.

The form named on the certificate and the standard used for the assay are part of the result, not of the cover page. A method run against a cyanocobalamin standard with an assumed response factor describes a different molecule.

Release tests for methylcobalamin · catalog specification
ParameterMethodRelease limit
AppearanceVisualDark red crystalline powder
IdentificationHPLC retention and UV-Vis spectrumConforms to the methylcobalamin reference
AssayHPLC with UV detection98.0–101.0%
Loss on dryingGravimetric≤10.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

Assay basis, water and the identity standard

The catalog line is 98.0–101.0% by HPLC and it does not carry a basis. Methylcobalamin holds water, and the loss-on-drying gate of ≤10.0% is wide enough that the basis can move the result beyond either end of that range. A powder measuring 94.0% as-is with 7.0% water calculates to 101.1% on the dried basis; the same analysis passes or fails depending on which basis is printed. The agreed specification should name the basis, and the certificate should repeat it in the assay row with the moisture result beside it.

The arithmetic matters at this dose. A 1,000 µg label claim is weighed as a milligram of powder, so the as-is assay is the figure that sizes the fill and the overage. An anhydrous figure is the right basis for a release limit because it separates the molecule from the water, but it is not the number to use at the balance.

Identity should be run against a methylcobalamin reference standard. The UV-Vis spectrum has maxima near 267, 342 and 522 nm, and the absorbance ratios at those maxima are fixed by the method; a retention time alone, without the spectrum, does not show which ligand sits on the cobalt.

Release limit versus batch result

A specification limit and a lot result answer different questions, and the certificate should keep them apart. The limit says what the lot had to meet; the result says what the laboratory found on the sample. Printing the range in both columns produces a document that looks complete and reports nothing. The result column should hold a number, a unit and a method reference for the sample actually tested.

What the result column should contain
ParameterRelease limitResult column
Assay98.0–101.0%, basis statedA measured percentage with the basis and the standard named
Loss on drying≤10.0%A measured percentage
IdentityConforms to the referenceRetention time, spectrum and the ratios used
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot

A pass statement is a conclusion, not a measurement. The reader should be able to rebuild it from the figures: a colony count plus an absence line for the micro tests, and a separate number for each metal. When the certificate gives one aggregated heavy-metal total, the element that drives the risk has disappeared into the sum.

What moves between batches

The colour, the moisture, the assay and the particle-size result move between lots. The final reaction step, the drying and the milling each leave a signature: drying moves the loss on drying, milling and sieving move the 80 mesh figure, and the crystallisation step moves the shade and the assay. A change of mill or sieve can move the particle-size line without any change in the chemistry, which is why that line belongs in the specification rather than in a note.

Colour is the least quantitative line and the least reliable early warning. Dark red covers a wide window, and the main degradation product is also red, so a shade difference proves neither identity nor failure. A lot that has seen light can lose assay while the appearance still passes. When colour is the only concern, ask for the chromatogram and the spectrum rather than rejecting the pack on a photograph.

A drift across several lots carries more information than one result near a limit: falling assay, rising moisture or an extra cobalamin peak. Traceability closes the loop, so the code printed on the certificate ought to be the same code on the pouch, the drum label and the sample kept in the retain cabinet.

When an outside test is worth ordering

An outside test earns its place at a new source, a first shipment into a regulated market, a disputed form or a light-damage concern. The panel then goes beyond the supplier's certificate: HPLC with a methylcobalamin standard plus a UV-Vis spectrum, the cobalamin profile for cyanocobalamin and hydroxocobalamin, loss on drying, ICP-MS for the metals and microbiology. Cobalt by ICP-OES lands near 4.4% for this molecule, but it cannot establish the ligand, because cyanocobalamin sits at 4.35% — too close to separate the forms on that number.

Every screen should come with its detection limit, because “not detected” only means something relative to the method's reach. A report that omits the limit describes the instrument, not the powder. Keep the chain of custody intact too: the portion that was tested should be the portion that was retained, and the report should carry the lot code.

What to compare between suppliers

Put six lines side by side: form and CAS number; assay result and basis; the identity standard and the spectrum; loss on drying; the cobalamin profile; pack size and lot code. Two quotations that agree on assay but differ on the standard or basis describe different powders.

Traceability comes next: who made the lot, which process and drying steps were used, and how the pack blocks light. The catalog specification sits on the methylcobalamin product page, and the cyanocobalamin 1% grade is a separate product with its own certificate. The tests that separate the methyl form from other cobalamins are on the identity page; the destination questions are on the compliance page; the HPLC method is described in the HPLC method note; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation