What the COA for choline chloride actually contains
The certificate for a choline chloride lot reports appearance, identification of choline and chloride, assay by titration, loss on drying, pH, particle size, the heavy-metal panel and microbiology. The assay can be a chloride titration, which counts the anion rather than the choline cation, so a choline figure and an amine limit belong beside it. The limits below are the catalog release gates; a given pack is proved by its own lot certificate.
The assay can count chloride while the label counts choline, so the certificate must name the titrant and report both figures.
Auditing a release certificate
Each line should let a reader check four things: what was measured, how, against which limit, and what the lot gave. A row that reads “conforms” asks the reader to accept a conclusion without the evidence. The table below sets out the catalog lines; the lot certificate adds the measured result and a lot code.
| Parameter | Method | Release limit |
|---|---|---|
| Identification | Choline and chloride by the named methods | Both conform |
| Assay | Titration — name the ion and the titrant | 98.0–101.0% |
| Choline | HPLC or ion chromatography | Report the measured figure |
| Loss on drying | Gravimetric | ≤1.0% |
| pH (10% solution) | Potentiometry | 6.0–8.0 |
| Total amines | Gas-sensing electrode, as trimethylamine | Report against the agreed limit |
| Heavy metals | ICP-MS | Pb 3 · As 2 · Cd 1 · Hg 0.1 (mg/kg, max) |
| Microbiology | Plate count and absence tests | E. coli and Salmonella not detected; TPC ≤1,000 cfu/g; yeasts and moulds ≤100 cfu/g |
| Particle size | Sieve analysis | ≥95% through 80 mesh |
Appearance is white to off-white powder. That line is weak on its own, because a deliquescent lot can look correct in the drum and be wet at the balance.
Which ion the titration measures
The United States Pharmacopeia monograph for choline chloride is explicit: the assay is a silver nitrate titration of chloride, with 0.1 N titrant and 13.96 mg of choline chloride per millilitre, and the result is calculated on the anhydrous basis. The reaction counts chloride ions. It assumes every chloride ion belongs to a choline molecule, which is true for a pure lot and false for a blend with sodium chloride or ammonium chloride.
The catalog line here says only “titration”. The certificate should name the titrant and the ion. If the laboratory uses the compendial silver nitrate method, the assay is a chloride figure; if it uses a choline-specific titration such as sodium tetraphenylborate, it is a cation figure. The two are not interchangeable.
The basis matters separately. The USP definition is 99.0–100.5% on the anhydrous basis with water not more than 0.5%; the catalog is 98.0–101.0% with loss on drying ≤1.0%. A lot at 0.8% water that reads 99.0% as-is calculates to 99.8% anhydrous. Both figures can be true, and they describe different powders.
The catalog window is also wider than the monograph at both ends. A lot at 98.5% meets the catalog and fails the USP definition; a lot at 101.2% does the same. A buyer who needs the monograph writes the monograph limits, not the catalog range.
Release limit, batch result and the basis
| Line | Release limit | Result column |
|---|---|---|
| Assay | 98.0–101.0%, basis stated | A measured percentage, the titrant and the basis |
| Choline | Agreed figure, about 74.6% at theoretical | HPLC or IC result with the method |
| Water | ≤1.0% catalog; ≤0.5% USP | Loss on drying or Karl Fischer, named |
| pH | 6.0–8.0 catalog; 4.0–7.0 USP | The concentration and the meter reading |
| Amines | ≤0.001% as trimethylamine, USP | The measured figure, not “absent” |
Two rows deserve a comment. The pH windows overlap but are not the same: a lot at pH 7.5 passes the catalog and fails the USP test, so the destination specification decides which applies. The amine limit is the odour line. A fishy note in the drum is a signal that the lot has been warm or alkaline, and a measured amine figure is more useful than a sensory comment.
“Passes specification” is a conclusion, not a result. The reader should be able to reach it from the numbers, the methods and the limits on the same page.
What moves between batches
Water is the first mover. Choline chloride is deliquescent, so an open pack takes up water, the loss on drying rises, the powder cakes and the as-is assay falls. The dry material has not changed; the water has. A certificate issued on a freshly opened drum can look better than the same lot after a week in a humid room.
pH moves with residual acid or alkali from the manufacturing step and can drift in a poorly sealed pack. The amine figure moves with heat and pH and is the line most often missing from a supplier's certificate. Particle size moves with the mill and the sieve; the 80 mesh figure is a finishing specification and can change without any change in the chemistry.
The chloride and choline figures should agree. Convert the assay to choline with 104.17 ÷ 139.62 = 0.746 and set it beside the HPLC result; a gap points to a chloride-bearing impurity, a dilution or a method problem.
When to use an outside laboratory
An outside laboratory earns its place when the source is new, the market is regulated, the result is contested, or the grade claims the USP monograph. The useful panel is not a repeat of the certificate: ion chromatography for chloride, HPLC for choline, Karl Fischer for water, ICP-OES for sodium and potassium, and a nitrogen test if an ammonium salt or urea is suspected.
Add the amine test and the residue on ignition. A lot spiked with sodium chloride raises the chloride titration and the ash while the choline figure stays low; a lot cut with a non-chloride carrier lowers both. The pattern of the two figures is more informative than either one alone.
Keep the chain of custody: test the retained sample, not a second scoop, and make the report name the lot. A “not detected” line without a detection limit is evidence about the method, not about the sample.
Six lines to compare between suppliers
Two quotations that agree on assay but differ on basis or amine limit are not describing the same powder. Put the six lines side by side before the first order.
| Line | What to ask | Why it matters |
|---|---|---|
| Form and CAS | Choline chloride, CAS 67-48-1? | The bitartrate carries a different choline figure |
| Assay and basis | Titration result; as-is or anhydrous? | A water-rich lot reads differently on each basis |
| Choline | HPLC or IC result and method? | The assay may count chloride, not choline |
| Water and pH | LOD or KF; 10% pH? | Deliquescence and acidity decide handling |
| Amines | Result against 0.001%? | The odour and quality signal |
| Pack and lot | Foil pouch, drum liner, lot code? | The barrier and the traceability |
The catalog values are listed on the choline chloride product page. The grade choice is on the grades page, the tests that prove the salt on the identity page, the chromatographic method in the HPLC note and the release workflow on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation