06 Identity & adulteration

How we prove a choline chloride lot is the chloride salt

Technical document 06 · Reviewed 2026-11-20 · Choline Chloride

On this page
  1. The five identity layers
  2. The ratio: 74.6 to 25.4
  3. X-ray diffraction and the solid state
  4. What substitution looks like
  5. Writing identity into the specification
  6. Five questions for the supplier

A choline chloride lot is the chloride salt when five lines agree: the document names the form and CAS number, infrared matches the reference, the chloride test is positive, choline is present by HPLC, and the choline-to-chloride mass ratio is close to the theoretical 74.6 to 25.4. The assay alone is not enough, because a chloride titration counts the anion and a chloride-bearing impurity can pass it without carrying any choline.

In one line

The chloride test proves the anion, the choline figure proves the cation, and the mass balance proves they belong to the same salt.

The five identity layers

Each layer answers a different question, and a supplier who reports only the assay has answered the narrowest one. The table below is the sequence to ask for, from paperwork to mass balance.

Five checks that make a choline chloride identity file
CheckThe question it answersMethodEvidence gained
PaperworkIs the substance named?Name, CAS and formulaIdentity on paper only
SpectrumDoes the whole molecule match?Infrared against a referenceThe organic part and its environment
AnionIs the counter-ion chloride?Silver nitrate or ion chromatographyThe chloride half of the salt
CationIs choline there, and how much?HPLC or ion chromatographyThe nutrient figure
BalanceCan the numbers belong to one salt?Assay, choline, water, ashEvidence against a blend

The infrared spectrum is the release identity in the USP monograph, together with the chloride test on a 1 in 20 solution. The spectrum covers the whole molecule, so it separates choline chloride from choline bitartrate and from a blend with a carrier. A certificate that says “IR conforms” without naming the reference has added little.

The ratio: 74.6 to 25.4

Choline chloride is a 1:1 salt. The choline cation is C5H14NO+ at 104.17 g/mol, the chloride ion is 35.45 g/mol, and the salt is 139.62 g/mol. The mass fractions are 104.17 ÷ 139.62 = 74.6% choline and 35.45 ÷ 139.62 = 25.4% chloride, so the mass ratio is about 2.94 to 1 and the molar ratio is 1 to 1.

That arithmetic is a check, not a label. A lot at 99.0% assay should carry about 73.9% choline and 25.1% chloride, with the remainder water and trace impurities. If the chloride figure is high relative to the choline figure, the lot contains a chloride salt that is not choline chloride. If both are low, the lot is diluted. The pattern points to the type of substitution before any extra test is ordered.

The USP assay is a silver nitrate titration of chloride, and each millilitre of 0.1 N titrant is equivalent to 13.96 mg of choline chloride. A sodium chloride addition raises that titration; the choline HPLC does not follow. That is why the two figures belong side by side, and why the assay basis — as-is or anhydrous — has to be stated.

X-ray diffraction and the solid state

Choline chloride is crystalline, so an X-ray diffraction pattern is a fingerprint of the solid. It can distinguish the salt from an amorphous carrier or a blend, and it can show sodium chloride as its own halite pattern when a chloride spike is crystalline. It does not measure choline and it does not prove the counter-ion on its own.

Sample preparation matters. Choline chloride is deliquescent, and a damp sample can lose the sharp pattern that a dry, freshly milled sample gives. Dry and handle the sample the same way each time, and ask for the reference pattern and the detection limit before accepting a “match”. XRD is not a routine release test; it is a dispute tool, read alongside the choline and chloride figures.

What substitution looks like

Choline chloride substitutions and the signals
SubstitutionWhat the buyer seesWhat catches it
Sodium chlorideChloride assay high; choline low; ash highCholine HPLC, sodium by ICP-OES, mass balance
Potassium or ammonium chlorideChloride assay high; choline low; pH may moveCholine HPLC, potassium or ammonium by IC
Betaine hydrochlorideChloride assay passes; no choline peak; IR differsCholine HPLC, IR, NMR
Urea or a nitrogen fillerChloride and choline both low; nitrogen highKjeldahl nitrogen, IR, choline HPLC
WaterLoss on drying high; as-is assay lowLOD or Karl Fischer, anhydrous calculation
Carrier dilutionBoth figures low; ash or fibre highAssay, choline, ash, microscopy

Colour and odour are weak signals. A white powder can be sodium chloride, and a fishy note points to amines rather than to the salt. The strong signals are the choline figure, the chloride figure, the ash and the sodium or potassium result. A certificate that reports only the chloride titration has left a likely substitution untested.

Writing identity into the specification

  • “Choline chloride, CAS 67-48-1, C5H14ClNO, molecular weight 139.62.”
  • “Identification by infrared against a reference and by the chloride test; both conform.”
  • “Assay 98.0–101.0% by titration, with the titrant, the ion and the basis stated.”
  • “Choline by HPLC or IC; report the measured figure and the method.”
  • “Water ≤1.0% by loss on drying, or ≤0.5% by the USP method where the monograph applies.”
  • “Total amines within the agreed limit, reported as trimethylamine.”
  • “Sodium and potassium by ICP-OES where the chloride-to-choline ratio is disputed.”

Five questions for the supplier

  1. Which method and which ion does the assay measure, and on what basis is it calculated?
  2. What is the choline figure by HPLC or IC, and what is the method?
  3. What are the water, pH and total amine results for this lot?
  4. Can you provide the infrared spectrum and the reference it was compared with?
  5. Will you re-test the retained sample jointly if the lot is contested?

Five answers of this kind make a file; one assay result does not. The product page carries the catalog values; the COA page maps each certificate line; the grades page covers the grade boundary; the ICP-OES note describes the sodium check; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation