How we prove a lot is adenosylcobalamin
The adenosyl ligand is what makes this cobalamin different, and the identity file has to prove it. A vitamin B12 assay cannot: methylcobalamin and cyanocobalamin respond to the same detection and carry the same red colour. The proof is a combination of chromatographic retention, a UV-Vis spectrum with the 375 nm band, a cobalamin profile and a mass balance.
The adenosyl ligand is the identity: the 375 nm band with the 522 nm visible band, read against an adenosylcobalamin standard, separates it from the methyl and cyano forms.
The four identity layers
Identity is built in layers, and each layer catches a different failure. Paperwork catches a naming error; chromatography catches the wrong ligand; the profile catches a co-eluting cobalamin; the mass balance catches a dilution. None of the four is sufficient alone.
| Layer | What it rules out | Evidence |
|---|---|---|
| Document | A mislabelled product | Name, CAS number and formula |
| Chromatography | Another upper ligand | HPLC retention against an adenosyl standard plus UV-Vis |
| Profile | A hidden cobalamin | Separate limits for methyl, cyano and hydroxo forms |
| Mass balance | A dilution or excess water | Assay, loss on drying and impurities |
A supplier who sends only a certificate with “B12 95%” has completed the first layer and skipped the other three.
The ratios that carry the identity
The UV-Vis ratios are the practical handle. In neutral solution the adenosyl spectrum has bands near 260, 375 and 522 nm; A375/A522 and A260/A375 are the two ratios a method can fix. Because the spectrum shifts with pH and solvent, the specification should state the ratios for its own method rather than borrow a number from another laboratory.
The chromatographic ratio is the second handle: adenosyl peak area against total cobalamin area. Set a separate limit for methyl, cyano and hydroxo cobalamins, so a small impurity of the closest analogue cannot hide inside a general purity figure. Cobalt at about 3.7% is a supporting check, not the proof.
HPLC and UV-Vis: proving the adenosyl form
The method must name the column, mobile phase, wavelength, solvent and reference standard. Retention alone is weak; the spectrum is the second dimension. An adenosyl standard is required for both identity and assay, and a degraded standard will move the retention and the spectrum together.
Sample handling matters more here than for a stable vitamin. The powder surface loses the adenosyl group under light, so weighing and dilution should be done in subdued light and the vial protected before injection. A low assay from a light-exposed sample can be an artefact, not a lot failure.
X-ray diffraction: the solid-state check
XRD answers whether the solid is crystalline and whether the pattern matches a reference. Adenosylcobalamin is sold as a crystalline powder, so the test has meaning for the pure grade; on a carrier dilution the carrier dominates the pattern, which itself shows what was added.
XRD does not identify the ligand and is not a purity assay. It is useful for a disputed lot or a source comparison, not as a routine release line. Ask for the reference pattern and the detection limit before accepting a “conforms” statement.
What adulteration looks like
| Adulterant | What it does | Signal | Test |
|---|---|---|---|
| Methylcobalamin | Closest analogue; similar colour and response | 342 nm band and retention differ; methyl peak present | HPLC/UV against an adenosyl standard |
| Cyanocobalamin | Cheaper, more stable; red and plausible | 361 and 550 nm bands; different retention | HPLC profile, UV-Vis |
| Hydroxocobalamin | Light-degradation product; still red | Extra peak and spectrum shift | HPLC profile, UV-Vis |
| Carrier dilution | Lowers the assay; adds a carrier | Assay low; loss on drying and ash move | Mass balance, carrier identification |
| Dye | Copies the colour, not the spectrum | No UV match | UV-Vis, HPLC |
The closest substitution is methylcobalamin, because it is also a coenzyme form and looks the same in a photograph. The strongest evidence against it is the 375 nm band and the retention time, not the colour.
How to write the identity into the specification
- “Material: adenosylcobalamin, CAS 13870-90-1, C72H100CoN18O17P.”
- “Assay: ≥95.0% by HPLC, adenosylcobalamin standard, basis stated.”
- “Spectrum: retention plus UV-Vis; maxima and ratios reported.”
- “Profile: separate results for methyl-, cyano- and hydroxocobalamin.”
- “Water: loss on drying ≤10.0%; contaminants per the panel.”
- “Size and pack: ≥95% through 80 mesh, light-resistant container.”
- “Route: destination, use and form fixed in writing before release.”
Questions to put to the supplier
- Which form and CAS number appear on the certificate for this lot?
- Please send the chromatogram and the complete UV-Vis spectrum, with the assay figure.
- Name the reference standard and the solvent used for the spectrum.
- Report the methyl, cyano and hydroxo cobalamin results separately for this lot.
- If a result is contested, will you re-test the retained sample jointly?
Keep those five answers with the lot record; one without the others leaves the file incomplete. The hub has the catalog specification, the COA page places each result, the grades page compares the physical forms, the level-four comparison follows the label and stability consequences, the methylcobalamin page covers the other form, the methods library explains the separation and the quality page describes release.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation