02.1 Pure vs wheat germ

Pure spermidine vs wheat germ extract: dose, purity and the label

Technical document 02.1 · Reviewed 2026-11-19 · Spermidine

On this page
  1. What the percentage is measuring
  2. The dose arithmetic
  3. Purity is not one number
  4. What the label has to carry
  5. When to choose which

Pure spermidine and a spermidine-rich wheat germ extract are not interchangeable at the same milligram. A 98.5% isolate carries about 985 mg of spermidine in every gram; the extract described in the EU authorisation carries 0.8–2.4 mg/g. A serving that supplies 6 mg therefore needs about 6 mg of the isolate or between 2.5 and 7.5 g of the extract. The capsule count, the label and the regulatory file all follow from that difference in mass.

In one line

A gram of 98.5% isolate carries about 985 mg of spermidine, while a gram of the authorised extract carries at most 2.4 mg — a difference that decides the capsule count, the label and the regulatory file.

What the percentage is measuring

Spermidine content per gram of each article
ArticleStated figureSpermidine per gramWhat the figure measures
Free base≥98.5%about 985 mgThe molecule as sold
Trihydrochloride98%about 559 mgThe salt, of which 57.0% is base
Wheat germ extract0.8–2.4 mg/g0.8–2.4 mgSpermidine content of the extract

The conversion is the first thing to do with any quotation. An isolate figure is a percentage of the molecule, and for a salt it has to be multiplied by the free-base fraction before it can be compared with anything else. An extract figure is already a content, expressed in milligrams per gram, and it applies to the extract powder rather than to the wheat germ it came from. Two quotations that both read “spermidine 98%” are only comparable once the form is named.

The 0.8–2.4 mg/g range is not a market average; it is the specification attached to the authorised article in the EU. An extract sold at 10 mg/g, which is 1%, is outside that range and is therefore not the article the entry describes, whatever its spermidine content. That distinction belongs in the specification and on the label.

The dose arithmetic

Arithmetic example · 6 mg spermidine, 500 mg capsules
ArticleMass for 6 mgCapsules at 500 mg
Free base, 98.5%about 6.1 mgWell under one
Trihydrochloride, 98%about 10.7 mgWell under one
Extract, 2.4 mg/gabout 2.5 gFive
Extract, 0.8 mg/gabout 7.5 gFifteen

Six milligrams is used here only because the EU entry caps the extract at the equivalent of 6 mg of spermidine a day. It is an arithmetic example, not a dose recommendation. What the table shows is the design space: an isolate serving is a few milligrams and disappears into a capsule fill, while an extract serving is grams and determines the dosage form. A stick pack, a powder for dispersion or a multi-capsule serving can carry the extract; a single small capsule cannot.

The same arithmetic explains dilution and granulation. When the active mass is a few milligrams, a production line needs a larger, more uniform powder to weigh accurately. A declared dilution solves a handling problem; an undeclared one changes the dose on the label.

Purity is not one number

For an isolate, purity is the assay of the named molecule. At 98.5% with water at ≤1.0%, the powder is almost entirely spermidine and the remaining fraction is water and related peaks. For a salt, the assay belongs to the salt: a 98% trihydrochloride is a pure salt that is 56% spermidine by mass. Calling it 98% pure and 56% active are both correct, and a label that uses one number without the other can mislead.

For an extract, “purity” is the wrong frame. The product is a mixture by design, with spermidine at 0.8–2.4 mg/g alongside spermine and the rest of the extract matrix. Its quality question is content and consistency, not a percentage of the whole. A buyer comparing “98%” with “0.2%” is comparing a molecule with a food ingredient, and the comparison says nothing about which one suits the product.

What the label has to carry

In the EU, the authorised extract has its own designation: the novel-food entry requires the extract to be labelled as a spermidine-rich wheat germ extract. The entry also restricts use to adult supplements, excludes pregnant and breastfeeding women, and caps the daily intake at the equivalent of 6 mg. Wheat sits among the cereals containing gluten in Annex II to Regulation (EU) No 1169/2011, so the allergen declaration has to be considered for the extract route.

An isolate, where it is lawfully used in the destination market, is named as the substance in the ingredient list, and the quantity per serving is declared in the supplement panel. In the US, the panel gives the amount per serving and no percentage when the ingredient has no Daily Value, and the source is named in the ingredient list. In both markets, the label describes the article that is in the pack, not the article that was considered during development.

This is a map of the questions, not legal advice. The current text of the novel-food entry, the allergen rules and the destination market's supplement rules should be checked before artwork is approved; the compliance page sets out the sequence.

When to choose which

The extract fits a product whose serving mass is already measured in grams, whose label can carry the wheat statement, and whose EU file is built around the authorised article. It also fits a positioning that depends on the extract as an ingredient rather than on a number of milligrams. The isolate fits a small capsule or tablet, a tight fill weight, a market where the isolate route is established, and a label that should not carry a cereal allergen.

What should not happen is a switch of source after the label is written. The two articles differ in content, allergen status, authorised designation and dose mass, so a change of source is a change of product. The source routes are compared at level three on the grade page; the certificate lines are on the COA page; the ordering units are on the MOQ page; the catalog specification sits on the spermidine product page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation