Pure spermidine or wheat germ extract: choosing a source
“Spermidine” on a quotation can mean two different articles. One is an isolated substance, typically ≥98.5% by GC or HPLC, with CAS 124-20-9 for the free base and a salt form available as well. The other is a spermidine-rich wheat germ extract, a mixed powder whose spermidine content is stated in milligrams per gram and which the EU lists as an authorised novel food at 0.8–2.4 mg/g. The two differ in dose mass, assay basis, allergen risk and regulatory file, so the source is a specification decision before it is a label decision.
The source route fixes the assay basis, the mass per dose and the regulatory file; it is a specification decision before it is a label decision.
Two articles under one word
The isolate is a single molecule. It can be supplied as the free base, a low-melting solid that may arrive crystalline or as a melt, or as a salt such as the trihydrochloride, which is a stable crystalline powder but carries only about 57% spermidine by mass. Beyond the molecule itself there is little else in the drum apart from water.
The extract is a mixture. It is made from wheat germ and sold on a stated spermidine content, and it also contains spermine and the rest of the extract matrix. In the EU the authorised article is defined, not generic: the Union list describes an extract of wheat germ that has not been fermented or germinated, specified at 0.8–2.4 mg spermidine per gram. That is under a quarter of one percent, which is the fact that changes everything downstream.
Neither route is a purer version of the other. They are different ingredients with different specifications, and a quotation that names only “spermidine” has not yet named the material.
The comparison that matters
| Source | Spermidine per gram | What the figure refers to |
|---|---|---|
| Free base, ≥98.5% | about 985 mg | Assay of the molecule as sold |
| Trihydrochloride, 98% | about 559 mg | Salt assay multiplied by the 57.0% free-base fraction |
| Wheat germ extract | 0.8–2.4 mg | Spermidine content of the authorised extract |
The table is arithmetic, not a grade ranking. A gram of isolate carries roughly four hundred times the spermidine of a gram of extract at the top of its range, and over a thousand times the spermidine of a gram at the bottom. That ratio, not the word on the front of the pack, decides how much powder a serving needs.
What the powder is like to handle
The isolate is white to pale cream, milled to 40 mesh and freely soluble in water. It is hygroscopic, so it wants a sealed liner and a dry room, and the melt form needs a defined handling temperature: a pouch that has been warm can arrive as a block even though the assay is unchanged. Because the dose is small, the analytical and weighing side of the process matters more than the bulk.
The extract is a larger mass of powder for the same spermidine figure, with its own colour, carrier and water content. Content uniformity is the practical issue: a low analyte level in a large powder mass has to be distributed evenly, and the certificate should state the spermidine result for the lot rather than a range copied from the specification. Wheat is a cereal that carries gluten, so the allergen question belongs at the grade stage, not at the artwork stage.
What the dose does to the dosage form
The EU entry for the extract is written as a maximum equivalent to 6 mg of spermidine a day. Using that figure only as an arithmetic example, 6 mg is about 6.1 mg of a 98.5% isolate, about 10.7 mg of a 98% trihydrochloride, 2.5 g of extract at 2.4 mg/g, or 7.5 g of extract at 0.8 mg/g. The first two fit in a small capsule; the last two do not fit in one.
That is the formulation consequence. A capsule or tablet programme is usually an isolate programme, because the mass is small and the fill weight is dominated by excipients. A stick pack, a drink mix or a multi-capsule serving can carry the extract, where the powder mass is part of the product rather than an obstacle. The same arithmetic explains why a dilution or a granulated form is sometimes offered: it makes a small dose weighable on a production line.
What to write into the specification
For an isolate, the specification names the form and its CAS, the assay method and basis at ≥98.5%, water at ≤1.0% by Karl Fischer, identity by GC or HPLC and IR, 40 mesh, the heavy-metal and microbiological panels, and the pack. For an extract, it names the spermidine content in mg/g with the method, the spermine and related-polyamine limits, the carrier, water, the metal and microbiological panels, the wheat and gluten statement, and the authorisation reference the article is sold against.
A specification that mixes the two is a specification for neither. “Spermidine ≥98.5%” cannot describe an extract at 0.8–2.4 mg/g, and “spermidine-rich wheat germ extract” cannot describe a 40 mesh isolate. Whichever route is chosen, the certificate, the label and the purchase order should use the same name.
Labels follow the article. In the EU the extract carries its novel-food designation, while an isolate, where it is lawfully used, is named as the substance; in the US the amount per serving goes on the panel without a percentage and the source goes in the ingredient list. A source change is therefore an artwork change, not a purchasing detail.
When the other route is the wrong one
The extract is the wrong choice when the serving would need more than two grams of powder, when the label cannot carry the wheat declaration, or when the content sits at the edge of the authorised range and the dose cannot absorb the variation. The isolate is the wrong choice when the destination market's file covers the extract article rather than an isolated substance, or when the product concept depends on the extract name itself.
The source route is compared in more detail on the pure versus wheat germ page. The certificate lines are set out on the COA page, the market question on the compliance page, and the packs and minimum on the MOQ page. The spermidine product page carries the catalog specification.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation