01 COA & batch testing

What the COA for R-alpha-lipoic acid actually contains

Technical document 01 · Reviewed 2026-11-20 · R-Alpha-Lipoic Acid

On this page
  1. The certificate as a test report
  2. Assay, basis and the mass balance
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

An R-alpha-lipoic acid certificate carries appearance, infrared and HPLC identification, assay by HPLC at 99.0–101.0%, specific rotation, melting point at 46–50 °C, loss on drying at ≤0.5%, heavy metals, microbiology and an 80 mesh sieve result. Read alone, the assay fits both optical grades, so the certificate proves the R form only when the rotation and the melting range are read beside it. The table below is the catalog specification; the batch certificate fills the result column for one pack.

In one line

A lipoic acid assay without a rotation and a melting range does not identify the R grade, and a percentage without its moisture basis does not identify the powder.

The certificate as a test report

For each parameter the reader needs the measurement, the method behind it and the limit the lot was released against. “Conforms” on its own records a decision and hides the number. The identity line should name infrared and HPLC together: the infrared spectrum carries the carboxyl band and the disulfide region, and the HPLC retention carries the whole molecule.

Identity, assay and release limits · R-alpha-lipoic acid
ParameterMethodRelease limit
AppearanceVisualYellow to pale yellow powder
IdentificationInfrared and HPLCConforms to the reference
AssayHPLC against an external standard99.0–101.0%
Specific rotationPolarimetry, c = 1, ethanol+110° to +125°
Melting pointCapillary method46–50 °C
Loss on dryingGravimetric≤0.5%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

Assay, basis and the mass balance

The assay is read against an external standard, which is why the window runs to 101.0% rather than stopping at 100%. A figure above 100% is a ratio to that standard, not permission to accept 103%. The certificate should also name the basis. At ≤0.5% loss on drying the two bases differ by at most about half a point, which is enough to cross the 99.0% limit. A lot read at 99.0% as-is with 0.5% water calculates to about 99.5% dried, and those two numbers describe different powders.

The rest of the mass balance sits in the other lines. Pure lipoic acid is 31.1% sulfur, so a sulfur figure well under that points to dilution rather than to weak material. The melting range and the rotation are the third and fourth checks, and both belong to the R grade rather than to lipoic acid in general. An achiral HPLC peak cannot separate enantiomers; rotation or a chiral column does that work, as the identity page sets out.

Release limit versus batch result

A limit is the boundary a lot was released against; a result is what the bench measured. Keep them in separate columns with the method beside each line. Copying the range into the result column answers nothing.

What the result column should contain
ParameterRelease limitResult column
Assay99.0–101.0% by HPLCMeasured percentage plus its basis
Specific rotation+110° to +125° (c = 1, ethanol)Measured value with solvent and concentration
Melting point46–50 °CStart and end of the measured range
Loss on drying≤0.5%Measured percentage
Heavy metalsPer elementmg/kg for each element
Particle size≥95% through 80 meshPercentage passing the sieve

The reader should be able to reach “passes” from the numbers without taking it on trust. Metals need a figure per element: one summed value hides which element failed. Rotation needs its solvent and concentration, and the melting result needs both ends of the range rather than a midpoint.

What moves between batches

Lot to lot, the assay, colour, moisture and sieve result follow the resolution step, the crystallisation and the milling. Rotation is the tightest line on the sheet and the one that carries the optical claim: material that has lost optical purity can still pass 99.0–101.0% by HPLC, because the achiral method sees both enantiomers as one peak.

The melting range is the second tell. A solid that melts at 46–50 °C sits close to summer warehouse temperatures, and a lot that has melted and set again is no longer the same powder: it can arrive as a glassy mass with a shifted range. A soft or caked drum is a handling question, not a cosmetic one, so read the batch record before rejecting on appearance.

A direction across several lots carries more weight than one result at an edge: rotation moving toward zero, assay drifting low, moisture climbing, or a melting range stuck at the bottom of the window. Pouch, drum and retained sample should all carry the code printed on the sheet.

When to order an outside test

An outside test earns its place with a new source, a first shipment into a regulated market, an optical claim the supplier's certificate does not support, or a disputed lot. The panel is not a copy of the certificate: chiral HPLC or polarimetry in ethanol for the form, infrared, melting point, loss on drying, ICP-MS and micro. Where dilution is suspected, add elemental sulfur.

Insist on the detection limit for every screen. “Not detected” without a limit says something about the method, not about the sample. The portion tested should be the retained portion, the report should name the lot, and a dispute should go to a referee laboratory both sides accept rather than to a second run of the same in-house method.

What to compare between suppliers

Six lines make two suppliers comparable: optical form and CAS number; assay and basis; rotation with solvent and concentration, plus the chiral result if one is offered; melting point; moisture, metals and micro; pack and lot code. Quotations that match on assay but not on form are describing different powders.

The specification is published on the R-alpha-lipoic acid page. The form comparison is on the grades page and at more length on the R form against racemic page; the assay method is described in the HPLC method note; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation