06 Identity & adulteration

How we prove a lot is R-alpha-lipoic acid

Technical document 06 · Reviewed 2026-11-20 · R-Alpha-Lipoic Acid

On this page
  1. The four identity layers
  2. The rotation and the enantiomer ratio
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Five questions for the supplier

A lot can be called R-alpha-lipoic acid when four results agree: the paper names the R form and CAS 1200-22-2, infrared and HPLC match the reference, the rotation or chiral result shows the R enantiomer, and the melting range with the moisture closes the balance. An assay of 99.0–101.0% cannot do that work alone; it fits the racemic grade, the R grade and every mixture in between.

In one line

Identity here is optical as well as chemical: the chromatogram shows lipoic acid, the rotation shows which enantiomer, and the melting point shows which solid.

The four identity layers

Paperwork can name the right material and still leave the powder unproved. The four layers are separate questions with separate evidence, and an answer to the first alone describes a document rather than a lot.

Four layers of R-alpha-lipoic acid identity
LayerQuestionMeasurementEvidence
DocumentWhich form is declared?Name, CAS number, formulaPaperwork
ChemistryIs the molecule lipoic acid?Infrared and HPLC retentionThe molecule, not the enantiomer
Optical formIs it the R enantiomer?Polarimetry or chiral HPLCEnantiomer and purity
Mass balanceDiluted or degraded?Assay, melting range, moisture, sulfurConsistency of the numbers

The rotation and the enantiomer ratio

Enantiomeric excess is the difference between the two enantiomers divided by their sum, expressed as a percentage. A lot at 99% ee holds about 99.5% R and 0.5% S; a racemic lot is 50:50. Polarimetry measures the net rotation of the sample, so partial racemisation lowers the reading while the assay stays put; chiral HPLC resolves two peaks and reports the ratio. Either method answers the optical question, and a certificate carrying neither has not addressed it.

The catalog sets rotation at +110° to +125° at c = 1 in ethanol. Solvent and concentration belong with the number, because rotation is a property of the solution as measured. A reading near zero is a signal for racemisation or for racemic substitution, and a reading below the window can mean S enrichment. The melting range supports the same conclusion from the solid side.

X-ray diffraction and the solid state

X-ray diffraction asks whether the solid is crystalline and whether the pattern matches a reference. The R enantiomer and the racemic compound pack differently, which is why they melt at 46–50 °C and 60–62 °C, and their patterns differ for the same reason. A pattern that matches the racemic reference is evidence of the racemic grade even when assay and infrared agree.

XRD is neither a chiral method nor a purity assay. It answers two useful questions: whether a lot is crystalline or an amorphous dilution, and whether two samples claiming one grade are the same solid form. Before accepting a “match”, ask for the reference pattern and the limit of detection. In a dispute, diffraction plus rotation plus HPLC outranks any one of them alone.

What adulteration looks like

Common R-alpha-lipoic acid substitutions and the signals
AdulterantWhat it doesSignalTest
Racemic gradeHalf the R content per milligramRotation near zero; melting point 60–62 °CPolarimetry, chiral HPLC, melting point
S-enriched materialLowers the R shareRotation below the window; ee lowChiral HPLC
DilutionLowers the assay and the sulfur figureAssay low; sulfur below 31.1%Mass balance, elemental sulfur
MoistureRaises loss on drying; lowers the as-is assayLoss on drying above 0.5%Loss on drying
Other disulfideSimilar colour and retentionExtra peak; spectrum mismatchHPLC, infrared, high-resolution MS

Colour is the weakest evidence. Yellow to pale yellow spans a wide range, and heat or light can darken a genuine lot. The stronger signals are rotation, chiral ratio and melting range, and they are quick to obtain next to the consequences of a rejected production batch.

How to write the identity into the specification

  • “R-alpha-lipoic acid, CAS 1200-22-2, C8H14O2S2, molecular weight 206.33.”
  • “Identification by infrared and HPLC; assay 99.0–101.0% by HPLC with the basis stated.”
  • “Specific rotation +110° to +125° at c = 1 in ethanol, with the chiral result if an ee limit is written.”
  • “Melting point 46–50 °C; loss on drying ≤0.5%.”
  • “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”
  • “No racemic substitution or dilution above the stated limit; optical form and destination confirmed before the order.”

Five questions for the supplier

  1. Which optical form is this lot, and which CAS number appears on the certificate?
  2. What rotation was measured, in which solvent and at which concentration?
  3. Will you send the chiral chromatogram or the polarimetry report, not just the assay figure?
  4. What melting range and moisture result were found, and how was the assay basis calculated?
  5. If the lot is challenged, will you join a re-test on the retained sample?

Those five answers, in writing, are an identity file. The specification is on the product page; the certificate layout is on the COA page; the racemic comparison is on the racemic product page; the label consequences are on the level-four page; the separations are described in the methods library.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation