How we prove a policosanol lot is the mixture it claims
A policosanol lot is the mixture it claims when four lines agree: the document names the source and the alcohol profile, the GC chromatogram shows the C24–C34 alcohols against reference standards, the octacosanol share matches the specification, and the melting point and moisture agree with the profile. The total alone cannot separate a sugarcane mixture from a rice bran mixture or from a spiked octacosanol blend.
Identity is the chromatogram plus the thermometer: a full alcohol profile against standards, the octacosanol share and a melting point that agrees with the mixture.
The four identity layers
A certificate may name the correct material without proving it. The four layers below are separate questions, and each one needs its own evidence. An answer to the first question alone describes paperwork, not powder.
| Layer | Question | Test | What it establishes |
|---|---|---|---|
| Document | Is the source and the profile named? | Name, source, specification version | Paperwork only |
| Chromatogram | Which alcohols are present, and in what proportion? | GC-FID full profile against reference alcohols | The mixture |
| Share | Is octacosanol the majority alcohol? | C28 peak against the declared basis | The label ratio |
| Thermal and mass balance | Does the solid agree with the profile? | Melting point, moisture, total | Consistency of the numbers |
The octacosanol share is a ratio, not a purity
Octacosanol is the C28 primary alcohol, CAS 557-61-9, formula C28H58O, molecular weight 410.76. The 60% figure is a share, and the certificate should say whether it is read against the total alcohol sum or against the powder. The difference is material: a lot at 90% total with a 60% share of the total carries 54% octacosanol by mass, while a 60% share of the powder carries 60%. Both can be described as “60% octacosanol” in a sales message, and they are different powders.
The chromatographic calculation has its own assumptions. Flame-ionisation response is roughly proportional to carbon mass within a homologous series, so area percentage is a reasonable approximation of mass percentage for the C24–C34 alcohols. It is still an approximation, and a method that uses reference standards and an internal standard is stronger than one that normalises the peaks. Area normalisation on a sample with non-eluting wax or solvent can overstate the share because the denominator is only the material that reached the detector.
A share can also be inflated by spiking. A lot built from a different wax and topped up with octacosanol can hit the 60% figure while the C26 and C30 peaks fall away from the source profile. The full chromatogram catches that; a single octacosanol number does not. Ask for the peak list and the reference standards, not only the percentage.
XRD is a supporting check, not a purity assay
X-ray diffraction answers a different question: is the solid crystalline, and does its pattern match a reference? Long-chain alcohols pack in layered crystals, and a mixture gives a pattern dominated by the majority alcohol plus the other components. It separates a crystalline alcohol mixture from an amorphous carrier or a waxy blend, and it can compare two sources. It is not a composition assay and it does not measure the octacosanol share.
For a disputed lot, XRD plus the GC profile plus the melting point is stronger than any one of them. Before accepting a “match”, request the reference pattern and the detection limit. “XRD conforms” with no pattern and no reference adds little. The melting point is the routine thermal check; XRD is the method to reach for when the solid form, not the assay, is the question.
Where substitutions show up
| Substitute | Effect | Signal | Check |
|---|---|---|---|
| Stearic acid or another fatty acid | Adds mass that is not a long-chain alcohol | Low melting point; extra peaks; acid value | GC with acid and alcohol separation; acid value |
| Octacosanol spiking | Raises the C28 share above the source profile | C26 and C30 low against C28; high, narrow melting point | Full GC profile; melting point |
| Another vegetal wax | Changes the C26, C30 and C32 pattern; adds esters | Extra peaks; ester or soap residue; source mismatch | GC, FTIR, source audit |
| Moisture | Lowers the as-is total | Moisture high; total low | Karl Fischer; mass balance |
| Residual solvent | Adds mass that is not an alcohol | Odour; headspace peak | Residual-solvent GC |
Colour proves the least. White to off-white covers a wide window, and a bleached or recrystallised lot can look the same as a clean one. The stronger signals are the full profile, the octacosanol basis and the melting point. A certificate that reports appearance and a total but not the peak list has left the most likely substitution untested.
How to write identity into the specification
- “Policosanol, mixed primary aliphatic alcohols, CAS 142583-61-7; octacosanol component CAS 557-61-9; source: sugarcane, rice bran or beeswax.”
- “Total policosanol ≥90.0% by GC-FID, sum of C24–C34 alcohols; method, column and reference standards named.”
- “Octacosanol share ≥60% by GC; state whether the figure is read against the total alcohol fraction or the powder.”
- “Full alcohol profile with C26, C28, C30 and the C32–C34 tail reported.”
- “Melting point 78–82 °C by a named method; moisture ≤1.0%.”
- “No dilution or single-alcohol spiking above the declared profile.”
- “Source and specification version under change control.”
Five questions for the supplier
- Which source is this lot, and can you provide the full GC profile with retention times and reference alcohols?
- Is the 60% octacosanol share read against the total alcohol fraction or against the powder?
- What is the melting point, and which method produced it?
- What are the moisture and total policosanol values for this lot, and how was the total calculated?
- For a disputed lot, would you join a re-test on the retained sample?
Those five answers together form an identity file. A single total percentage does not. The catalog values are on the policosanol product page; the COA page maps each figure to its certificate line; the grades page compares the sources; the level-four comparison separates the mixture from the single alcohol; the methods library explains the GC separation.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation