Policosanol grades: source, profile and octacosanol share
Policosanol is sold by source and by profile, not by a single purity number. Sugarcane wax, rice bran wax and beeswax yield different distributions of C24–C34 alcohols, and a 90% total with a 60% octacosanol share from one source is not the same material as a 90% total from another. The grade decision is therefore a source decision plus an octacosanol-share decision.
The grade is the source plus the profile: sugarcane, rice bran and beeswax give different alcohol distributions, and the octacosanol share is what the specification should name.
A mixture has no single assay to grade on
The 90% figure is a sum of alcohol peaks, and two lots can both meet it with different proportions of C26, C28 and C30. One may be octacosanol-dominant, the other richer in triacontanol; both can be called policosanol 90%. The number alone does not tell a formulator which powder is in the drum, and it does not tell a label reviewer whether the declared ingredient matches the material.
The grade is not a ladder from a low percentage to a high one. It is a set of source profiles that meet different labels. A sugarcane-derived concentrate, a rice bran-derived concentrate and a beeswax-derived concentrate are three starting points, and the refining sequence then decides how much of the non-alcohol wax is removed. A buyer who orders “policosanol 90%” without a source and an octacosanol share has specified one number out of four.
The three sources side by side
| Source | Typical dominant alcohols | Profile character | What to watch |
|---|---|---|---|
| Sugarcane wax | C28 octacosanol, then C30 triacontanol and C26 hexacosanol | Usually the highest octacosanol share of the three | Wax refining; residual solvent; granulation |
| Rice bran wax | C28, C30 and C32 in variable proportions; some lots are triacontanol-rich | Octacosanol present, not always dominant; fractionation sets the share | Rice bran oil co-product; ferulate esters are a separate stream; check the C28/C30 ratio |
| Beeswax | C24–C34, often triacontanol-rich | Broader profile, lower octacosanol share | Requires hydrolysis; ester and odour removal |
The table is qualitative on purpose: the certificate should carry the measured numbers, not a source average. The same source can produce a different profile from a different refiner, and the same refiner can shift the profile when it changes the fractionation. The catalog's ≥60% octacosanol share is a specification the refiner has to meet, not a property of every wax; the certificate should show the measured result. Rice bran is also the source of gamma-oryzanol, a ferulate ester stream that is a different product with a different assay; the two should not be confused when a rice bran wax lot is described.
Melting point, solubility and the powder
The catalog form is a white to off-white powder with a melting point of 78–82 °C. It is insoluble in water and soluble in ethanol and in warm fats and oils. The melting range is a mixture property: it is not sharp like a pure compound, and both edges are part of the specification. A narrow result at the upper edge points to a more octacosanol-rich fraction; a result at the lower edge points to more C26 or C30, or to residual esters, soaps or solvent. The melting point is a fingerprint, not a purity assay.
Particle size and granulation are separate decisions. The catalog powder can be granulated on request for flow, dust control or tablet compression, and a granulated grade needs its own total and profile because a carrier or a binder changes the mass per gram. Granulation does not change the chemistry, but it changes the fill weight, the disintegration behaviour and the appearance of the finished dose.
The melting range also matters in processing. A melt held above 82 °C and then cooled sets into a waxy solid, and the cooling rate changes the crystal size and the flow of the solidified material. A process that heats policosanol should state the hold temperature and the cooling step, not only the storage condition.
The label figure and the dosage form
Capsules, tablets and powder blends are the usual formats. The label should be built on the measured total, not on the assumption that 90% means a full 900 mg of alcohols in every gram after granulation or blending. A 500 mg capsule of a 90% powder carries 450 mg of total alcohols; at a 60% octacosanol share of the total it carries 270 mg of octacosanol, while a 60% share of the powder would give 300 mg. The certificate's basis decides which arithmetic applies, and the label should use the same basis.
That arithmetic is a label exercise, not a dose recommendation. The point is that the declared policosanol and the declared octacosanol have to come from the same profile, and a switch of source or granulation can move both figures without a change in the product name. A diluted grade changes the mass per capsule again, and a formulator who keeps the old fill weight will under-deliver the declared alcohol figure.
The lipid story is claim-sensitive, and the label wording is a separate review from the specification. The compliance page sets out the documents and the route question; the specification should not be written around a claim.
What to write into the specification
- “Policosanol, mixed primary aliphatic alcohols, CAS 142583-61-7; octacosanol component CAS 557-61-9; source: sugarcane, rice bran or beeswax.”
- “Total policosanol ≥90.0% by GC-FID, sum of C24–C34 alcohols; method, column and reference standards named.”
- “Octacosanol share ≥60% by GC; state whether the figure is read against the total alcohol fraction or the powder.”
- “Full alcohol profile with C26, C28, C30 and the C32–C34 tail reported, not only the total.”
- “Melting point 78–82 °C by a named method; moisture ≤1.0%.”
- “Heavy metals and microbiology as listed; particle size or granulation if the dosage form needs it.”
- “Source and specification version under change control.”
We supply the mixture. A single-alcohol octacosanol grade is a separate purchase with its own assay and label; substituting it needs a written change control.
When another grade is the wrong buy
If the label names octacosanol as the ingredient, a policosanol mixture is not a drop-in: the declared substance and the weighed substance would differ, even if the octacosanol figure is close. If the market file or the customer statement names a source, a switch from sugarcane to rice bran or beeswax is a specification change, not a supply convenience. If the dosage form needs a free-flowing granule, the standard powder may flow poorly and segregate in a blend.
The reverse is also true. A buyer who needs the mixture for its natural profile should not accept a single-alcohol grade as “the same thing at a higher percentage”. The catalog values are on the policosanol product page; the level-four comparison sets out the mixture against the single alcohol; the COA page shows how the profile is reported; the quality page covers the release workflow.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation