02 Grade comparison

Melatonin 99% or a 1% dilution: choosing a grade

Technical document 02 · Reviewed 2026-11-19 · Melatonin

On this page
  1. “99%” is an assay window, not a fixed strength
  2. The two grades side by side
  3. Mesh, flow and static
  4. What the unit can carry
  5. What changes when you switch
  6. When the other grade is the wrong answer

The catalog grade is a crystalline powder assayed at 98.5–101.5% on the dried basis and sold in the trade as “melatonin 99%”. The alternative is a 1% dilution: one part melatonin to 99 parts carrier by mass, made so that a small amount of melatonin can be weighed and blended accurately. The choice turns on the mass a unit can carry and the weighing accuracy of the plant, not on a stronger or weaker effect.

In one line

The grade is a handling decision: crystalline powder when the unit can carry and weigh it, a 1% dilution when the melatonin mass per unit is too small for accurate weighing.

“99%” is an assay window, not a fixed strength

The figure is shorthand for the 98.5–101.5% release window. A certificate result anywhere between 98.5% and 101.5% meets the catalog, so the batch COA, not the trade name, is the number that applies to the drum. A trade name that says 99% is a round statement about a window; the certificate is the evidence behind it.

The 1% dilution is a pre-blend, not a second purity grade. Nominally it carries 10 mg of melatonin per gram, and the actual content is on the dilution's COA. The carrier is named in the specification and in the finished product's ingredient list. It is not a carrier that can be assumed from the word “dilution”.

The catalog lists three formats: crystalline powder at 40 mesh, a 1% dilution on request, and a granulated form on request. Granulation changes flow and dust, not the assay window. The grade and the physical form are separate decisions, and a quotation should name both.

The two grades side by side

Crystalline melatonin and a 1% dilution · what differs
ParameterCrystalline grade1% dilution
Melatonin content98.5–101.5% (dried basis)1.0% nominal; assay on the dilution COA
Melatonin per gram985–1,015 mg10 mg nominal
Powder mass for 1 mg melatoninAbout 1.0 mgAbout 100 mg
CarrierNoneAbout 99% of the powder mass
Typical unitCapsule, tablet, larger stick packLow-dose capsule, stick pack, small batch
Analytical workAssay, loss on drying, related substancesPlus carrier identity and blend uniformity

The table is arithmetic, not a ranking. The pure grade is not “better” and the dilution is not “weaker” in the sense of quality; they put different masses of the same molecule into the same unit. What changes is how much powder the unit must hold and how much of the fill is carrier.

Mesh, flow and static

40 mesh is a sieve opening of about 425 µm. The crystalline powder is light, and static can make it cling to a scoop, a blender wall or a pouch. At a milligram target that cling is a real weighing error, not a housekeeping detail. The pure grade rewards a plant that can control humidity, grounding and weighing tolerance.

The 1% dilution's flow depends on the carrier. If the carrier is coarser or denser than the melatonin, the blend can segregate in a hopper; if it is finer, the blend can dust. The carrier's particle size should be matched to the melatonin and to the mixing equipment, and the blend should be validated rather than assumed. Granulation can reduce dust and improve flow, but it is a third format, not a fix for a badly matched carrier.

What the unit can carry

The fill weight is set by the capsule size, the tablet weight or the stick-pack fill, and by the blend's bulk density. The melatonin mass is a fraction of that fill. A 1 mg target from the crystalline grade is about 1 mg of powder; from the 1% dilution it is about 100 mg. The first is difficult to weigh on a production scale, the second is easy to weigh but uses 100 mg of the fill.

A 5 mg target is about 5 mg of the crystalline powder or about 500 mg of the 1% dilution. If the capsule cannot hold 500 mg, the dilution is the wrong choice. A 0.5 mg target is about 0.5 mg of the pure powder or about 50 mg of the dilution, and the pure powder is usually below the reliable weighing range of a production balance. These are mass calculations for formulation, not intake instructions.

The same arithmetic applies to a stick pack. A 2 g fill of a 1% dilution carries about 20 mg of melatonin; the same fill of the crystalline grade would carry about 2 g, which is far outside a low-dose unit. The dilution is what makes a small target compatible with a large fill.

What changes when you switch

Switching grade changes the assay basis, the loss on drying, the mesh, the microbiological load, the label, the stability and the blend validation. The dilution's COA should report the melatonin content of the blend, the identity and specification of the carrier, and the uniformity of the blend. The pure lot's COA should be available as the input, so the dilution can be traced back to a released lot.

The label changes with the grade. The finished product declares the amount of melatonin, not the mass of the pre-blend, and the carrier belongs in the ingredient list. In the US the Supplement Facts panel carries the melatonin quantity; in the EU the ingredient list and the nutrition declaration carry the declaration. A label that calls a 1% blend “99% melatonin” is wrong on its face.

Order quantity changes too. One kilogram of the crystalline grade contains about 990 g of melatonin; one kilogram of the 1% dilution contains about 10 g. A trial that needs 100 g of melatonin needs about 101 g of the pure powder or about 10 kg of the dilution. The minimum order is the same 1 kg pack, but the active mass behind it is not.

When the other grade is the wrong answer

The crystalline grade is wrong when the unit needs less than the plant can weigh reliably. The 1% dilution is wrong when the unit cannot carry the carrier mass, when the label cannot declare the carrier. Granulation is wrong when the application needs a fine powder and the flow problem is really a carrier problem.

Do not switch grade to fix a microbiological result, a colour issue or a label claim. Those are separate controls, and a new grade brings a new carrier, a new blend step and a new set of evidence. The dose, blend and label consequences of the switch are worked through on the 99% versus 1% page.

The catalog values are on the melatonin product page; the certificate lines are on the COA page; the pack sizes and the 1 kg minimum are on the ordering page. The assay term is defined in the assay glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation