06 Identity & adulteration

How we prove a low-MW hyaluronic acid lot is hyaluronan

Technical document 06 · Reviewed 2026-11-20 · Hyaluronic Acid Low MW

On this page
  1. The five identity layers
  2. The disaccharide ratio and the distribution
  3. X-ray diffraction: what it cannot show
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Five questions for the supplier

A low-MW hyaluronic acid lot is the named material when five lines agree: the document names the form, the CAS number and the grade band; the HPLC assay is reported on a stated basis; the IR spectrum matches a reference; SEC-MALS returns a molecular weight inside 20–80 kDa; and the mass balance closes with moisture and protein. The ≥95.0% assay alone cannot show chain length or catch a dilution. The grade has to be measured, not inferred from viscosity.

In one line

Identity is five agreeing measurements: the named form, the HPLC assay, the IR fingerprint, the 20–80 kDa window and a mass balance that closes.

The five identity layers

No single test carries the conclusion. A correct document can sit beside a diluted powder, an assay can pass on a chain of the wrong length, and a molecular weight inside the band does not rule out another glycosaminoglycan. The layers fail in different ways, so the file is complete only when all five agree.

Five identity layers for low-MW hyaluronic acid
LayerQuestionEvidenceWhat it proves
DocumentIs the form, CAS and grade named?Name, CAS number, 20–80 kDa bandPaperwork only
AssayHow much hyaluronan is present?HPLC against a standard, on a stated basisMass of the polysaccharide
SpectrumIs the polymer hyaluronan?IR against a referenceThe functional groups
Chain lengthIs it the low band?SEC-MALS average and distributionThe grade
Mass balanceIs it diluted?Assay, loss on drying, proteinConsistency of the numbers

The disaccharide ratio and the distribution

Hyaluronan is a linear chain of one repeating disaccharide: D-glucuronic acid joined to N-acetyl-D-glucosamine in a 1:1 molar ratio. In the acid form the repeat unit has a formula mass near 379 g/mol; the glucuronic acid residue contributes about 176 g, or 46.4% by mass, and the N-acetylglucosamine residue about 203 g, or 53.6%. A glucuronic acid result close to that proportion supports the polysaccharide; a figure well below it points to dilution or to a different polymer. For the sodium salt the repeat is about 401 g/mol and the glucuronic acid share falls to about 43.9%, which is why the form has to be named before the ratio is read.

The ratio only means something when both figures share a basis. If the assay is on the dried solids and the glucuronic acid is on the powder as sold, the two cannot be divided by each other until the moisture is reconciled. The catalog does not print a glucuronic acid limit, so this is a supplementary identity test rather than a release line; it is most useful when a lot is disputed or a new source is being qualified.

The second ratio is the molecular-weight distribution. An average inside 20–80 kDa can hide a broad or bimodal distribution, and a blend of a short and a long chain can report the right average while behaving unlike the grade. Ask for the weight-average, the number-average and the shape of the distribution, not only the single figure that meets the window.

X-ray diffraction: what it cannot show

An amorphous polymer does not give a useful diffraction fingerprint, so XRD cannot establish that a powder is hyaluronan. The pattern is a broad halo with no sharp reflections, which confirms only that the solid is non-crystalline. A claim that it “matches the reference” adds little unless the pattern and the reference are attached.

The test still has a narrow use. A crystalline diluent such as a sugar or sodium chloride can produce sharp reflections above its detection limit, so a pattern that is not a pure halo is a reason to look at the formulation and the batch record. Ask for the detection limit before reading a clean halo as proof of purity; the method sees crystalline phases, not the chain length or the protein. The XRD method note sets out the limit.

What adulteration looks like

Common low-MW hyaluronic acid substitutions and the signals
RouteWhat it doesSignalTest
Maltodextrin or dextrinAdds mass; lowers assay; raises moistureAssay low; IR differs; LOD highHPLC, IR, loss on drying
Another glycosaminoglycanShares the uronic acid building blockIR and HPLC profile differ; protein may moveIR, HPLC, protein, molecular weight
High-MW material sold as lowAverage outside the band or bimodalSEC-MALS average high; solution too thickSEC-MALS distribution
Added waterLowers the as-is assay; cakingLOD high; dry-basis assay normalLoss on drying
Form substitutionSalt sold as acid, or the reverseName and CAS mismatch; IR carboxylate region shiftsIR, pH, sodium by ICP-OES

Each route leaves more than one mark, and no single test catches all of them. The workable screen combines the document, the assay on a stated basis, IR, SEC-MALS, moisture and protein, all run on one submitted sample that carries the lot code.

How to write the identity into the specification

  • “Hyaluronic acid, low molecular weight, CAS 9004-61-9, with the form named.”
  • “Assay ≥95.0% by HPLC, with the basis printed on the certificate.”
  • “Identification by HPLC retention and IR against a reference; report the spectrum.”
  • “Molecular weight 20–80 kDa by SEC-MALS; report the average and the distribution.”
  • “Loss on drying ≤10.0%; protein ≤0.1%; ≥95% through 80 mesh.”
  • “No diluent or other glycosaminoglycan above the agreed limit.”
  • “Source, hydrolysis step and destination market confirmed before the order.”

Five questions for the supplier

  1. Which form and CAS number are on the certificate, and does the label use the same name?
  2. Is the 95.0% assay on the powder as sold or on the dried solids, and what is the loss on drying for this lot?
  3. Can you send the IR spectrum and the HPLC chromatogram, not only the conformity statement?
  4. What are the weight-average and number-average molecular weight by SEC-MALS, and what does the distribution look like?
  5. In a dispute, will you test the retained sample jointly with our laboratory?

Answered directly, these five points make an identity file; one assay figure does not. The product hub carries the catalog ranges; the COA page shows where each number sits on the certificate; the grades page compares the bands; the FTIR method note explains the spectrum; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation