02 Grade comparison

Low or high molecular weight: choosing a hyaluronic acid grade

Technical document 02 · Reviewed 2026-11-20 · Hyaluronic Acid Low MW

On this page
  1. Why molecular weight is a grade
  2. The bands side by side
  3. Viscosity, dissolution and handling
  4. Dose, format and the label
  5. What to write into the specification
  6. When the low band is the wrong choice

Low-molecular-weight hyaluronic acid is a chain-length grade rather than a different molecule: the 20–80 kDa catalog window sits below the 1.0–1.5 MDa food-grade material, and the two behave differently in water at the same solids. The grade changes the viscosity, the dissolution, the amount of powder that fits a stick or capsule and the grade wording a label can defend. The acid or salt form is a second decision, not part of the grade.

In one line

The grade is a chain length: 20–80 kDa and 1.0–1.5 MDa share the same repeat unit, and the difference appears in viscosity before it appears on the label.

Why molecular weight is a grade

Hyaluronan is a linear polysaccharide built from one repeating disaccharide: D-glucuronic acid and N-acetyl-D-glucosamine, joined in a fixed alternation. The chemistry of the repeat does not change with the chain length. What changes is how many repeats are joined end to end, and with it the hydrodynamic volume the molecule occupies in water.

A low-molecular-weight grade is made by controlled hydrolysis or by fermentation and recovery to a shorter chain. The result is the same repeat unit at roughly 50–210 units instead of the thousands found in the high-molecular-weight material. The assay can read the same on both, because it counts the polysaccharide mass, so the molecular-weight line is the only place the grade is visible on a certificate.

The catalog keeps the two as separate products for that reason. A buyer who orders “hyaluronic acid” without a band has not specified the powder; a quotation that names only the assay has not quoted the grade.

The bands side by side

Low and high molecular weight hyaluronic acid
AttributeLow MW (this product)High MW
Catalog band20–80 kDa by SEC-MALS1.0–1.5 MDa
Approximate repeats50–210 disaccharides2,600–4,000 disaccharides
Viscosity at equal solidsMuch lowerMuch higher
DissolutionFaster; clears soonerSlower; tends to lump
Solids load in a drinkHigher before it thickensLower
Usual formatsSticks, drink mixes, capsulesCapsules, tablets, low-solids sticks

Neither band is a legal category. Suppliers draw the boundaries in different places, and a number from another source means something only when its method is known. This catalog measures the low band by SEC-MALS; a viscometry value is a different average.

Viscosity, dissolution and handling

Viscosity belongs to a solution, not to a bag of powder. Concentration, temperature, shear rate and the instrument all change the number, so two figures are comparable only when those conditions match. One general statement holds: for the same concentration, the shorter chain gives the thinner solution, and the gap widens as concentration rises.

The longer polymer wets slowly, and the outer layer of a lump can gel before water reaches the centre. The shorter chain wets and clears sooner, which is the practical reason it suits a sachet or a glass. Passing 80 mesh improves dispersion, but the sieve does not alter the chain or the thickness of the final solution.

Both bands take up water. The low band has more chain ends per gram, so an open pouch in a humid room can cake quickly. The 10.0% loss-on-drying limit is an acceptance test, not a storage allowance; the pack and the dose-room humidity belong in the specification.

Dose, format and the label

Here, dose means the mass of hyaluronic acid stated per serving, not an intake recommendation. A 500 mg serving of a 95.0% powder supplies 475 mg of hyaluronic acid; the balance is water and the residue the specification permits. The grade does not alter that sum, but it changes how much powder the format can hold.

A capsule has a fixed fill volume, so flow and bulk density matter more than viscosity there. A stick is a dry blend that the customer dissolves, so the grade controls how quickly it clears and how thick the drink turns. In a ready-to-drink product, clarity joins the same trade: the low band carries more solids before the liquid becomes hard to pour or unpleasant to drink.

The label normally names the ingredient rather than the band. If the artwork adds “low molecular weight”, that phrase is a descriptor or a claim and needs the certificate behind it. The market review of that wording is separate from the specification, and no disease claim is available in either case.

What to write into the specification

  • “Hyaluronic acid, low molecular weight, CAS 9004-61-9, with the form named.”
  • “Assay ≥95.0% by HPLC, with the basis stated on the certificate.”
  • “Molecular weight 20–80 kDa by SEC-MALS; report the average and the distribution.”
  • “Identification by HPLC retention and IR against a reference.”
  • “Loss on drying ≤10.0%; protein ≤0.1%; ≥95% through 80 mesh.”
  • “Heavy metals and microbiology to the listed limits; destination market confirmed before the order.”

When the low band is the wrong choice

If the formula needs thickness at a low mass, the high band does that with less powder. If the product is a small capsule or tablet and the label declares a modest amount, the high band may be the simpler fit. If the market file or the label names the sodium salt rather than the acid, the form question has to be settled before the grade question, because the two names are not interchangeable on a specification.

Changing band is a change control, not a substitution. Check viscosity at the intended concentration, the dissolution time, stability in the finished pack and the label wording again. The product hub carries the catalog specification; the level-four comparison takes the viscosity and label questions further; the high-molecular-weight product page is the other side of the range; the stability page covers the storage behaviour; the analytical methods index explains the measurements.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation