01 COA & batch testing

Reading a glucosamine sulfate COA, line by line

Technical document 01 · Reviewed 2026-11-20 · Glucosamine Sulfate

On this page
  1. The certificate as a test report
  2. The assay basis and the sulfate basis
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

The certificate for a glucosamine sulfate 2KCl lot reports appearance, identification by HPLC and sulfate, assay by HPLC, sulfate by titration, loss on drying, the heavy-metal panel, microbiology and particle size. The assay and the sulfate figure are read together: one counts the amino sugar, the other counts the counter-ion. A certificate that reports only the assay has not shown which salt the lot contains. The limits below are catalog values; the batch certificate confirms a particular pack.

In one line

The assay and the sulfate figure are two halves of one identity: the HPLC counts glucosamine, the titration counts sulfate, and a useful certificate reports both against their limits.

The certificate as a test report

An auditable certificate gives every row the same three columns: the parameter, the analytical method behind the number, and the limit the lot had to satisfy. “Conforms” on its own is a verdict; it does not show what the laboratory measured.

The identification line establishes the 2KCl sulfate complex, the assay line fixes the glucosamine content, and the sulfate line fixes the counter-ion and its stoichiometry. A certificate that rolls those three into a single percentage has removed the evidence that separates this salt from glucosamine hydrochloride.

Identity, assay, sulfate and contaminants · glucosamine sulfate 2KCl
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
IdentificationHPLC retention and sulfate reactionConforms to the reference
AssayHPLC98.0–102.0%
SulfateTitration15.0–17.0%
Loss on dryingGravimetric≤1.0%
Heavy metals (Pb, As, Cd, Hg)ICP-MS, one result per elementPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
Microbiology (APC, yeast/mould, pathogens)Plate count; absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle size (80 mesh)Sieve analysis≥95% through 80 mesh

The assay basis and the sulfate basis

Glucosamine sulfate is a 2:1 salt: two glucosamine molecules to one sulfate, and the commercial solid adds two potassium chloride units. The formula mass of the complex is about 605.5, and sulfate is 15.9% of that mass at full stoichiometry. The catalog range of 15.0–17.0% is built around that figure. A result near the middle is consistent with the complex; a result near an edge should be read with the assay beside it.

The assay is reported against a glucosamine standard, and the certificate should say whether the result is calculated on the dried basis or on the powder as received. With loss on drying limited to ≤1.0%, the difference is at most about one percentage point, but it still changes the number. A 100.0% result as-is at 0.8% moisture is 100.8% on the dried basis; the two descriptions are not interchangeable.

Ask whether the sample was hydrolysed before the assay: a method that measures glucosamine after hydrolysis and one that measures the intact salt against a sulfate standard do not report the same number, even when both are called HPLC. The method line should name the standard and the basis, and the sulfate result should carry its basis too.

Release limit versus batch result

On the certificate, the limit is the boundary and the result is the measurement. Keep them in separate columns and put the method beside them. If the result column simply repeats the specification range, the reader has been given the gate again, not the lot.

What the result column should contain
ParameterRelease limitResult column
Assay98.0–102.0% by HPLCMeasured glucosamine, with standard and dried/as-is basis
Sulfate15.0–17.0% by titrationMeasured sulfate, with titrant and calculation
Loss on drying≤1.0%Measured moisture and oven temperature
Heavy metals (Pb, As, Cd, Hg)Four elements, each with its own limitOne ICP-MS result per element, in mg/kg
Microbiology (APC, yeast/mould, pathogens)Counts plus absence testsPlate count, yeast/mould count and absence findings
Particle size (80 mesh)≥95% through 80 meshMeasured percentage passing the sieve

“Passes specification” is a conclusion, not a measurement; the reader should be able to rebuild it from the figures. Microbiology needs a count and an absence statement, and heavy metals need a figure per element rather than a single total.

What moves between batches

Between lots the sulfate figure, the assay, the loss on drying, the colour and the particle-size result move. The first two should move together. If the complex is consistent, a glucosamine assay near the top of the range comes with a sulfate figure close to 15.9%, not with a sulfate figure at 13%. A lot that reports 101% assay and 13.5% sulfate is not a slightly better version of the same powder; it is a different composition, and the chloride line would show whether the hydrochloride has entered the lot.

Potassium and chloride are not on the catalog specification, but they are the second half of the 2KCl story. The complex carries about 12.9% potassium and 11.7% chloride, or about 24.6% potassium chloride. A potassium result well below that figure points to the sodium form or a dilution; a potassium result above it points to added potassium salt. Request both when the source or the form is new.

Colour is a weak signal. White to off-white covers a range, and a slightly cream batch is not necessarily out of specification; a yellow or brown cast suggests moisture, heat or a reducing sugar has acted on the powder, so read it with loss on drying and the storage record. The 80 mesh result is a finishing line: it can change with the mill or sieve without any change in the chemistry.

When to order an outside test

Order an independent test for a new source, a first shipment into a market where the allergen file matters, a form claim the supplier's certificate does not prove, or a disputed result. The panel is HPLC with the glucosamine standard and the stated basis, sulfate by titration, potassium by ICP-OES and chloride by titration, ICP-MS for the metal panel, microbiology and a sieve check. Add XRD or FTIR if the solid form is in question.

Require a detection limit for every screen; a “not detected” entry without one describes the method, not the sample. Chain of custody still matters: the sample tested should be the retained sample, and the report should carry the lot code from the pouch or drum. If a result is disputed, hand the referee the retained sample, the supplier's certificate and the specification, and ask for the tests that separate the forms rather than another run of the same assay. The analytical methods library describes the tests.

What to compare between suppliers

Put seven lines side by side: form and CAS number; assay result and basis; sulfate result and method; potassium and chloride; loss on drying; heavy metals and microbiology; source and allergen statement. Two quotations that agree on assay but differ on sulfate or on source are not describing the same powder.

The catalog specification is on the glucosamine sulfate product page. The tests that separate the complex from the hydrochloride are on the identity page; the salt comparison is on the grades page; the HPLC method is described in the HPLC method note; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation