06 Identity & adulteration

How to prove a glucosamine sulfate 2KCl lot

Technical document 06 · Reviewed 2026-11-20 · Glucosamine Sulfate

On this page
  1. The four identity layers
  2. The sulfate ratio and the mass balance
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A glucosamine sulfate 2KCl lot is the named complex when four lines agree: the document names the form and CAS number, HPLC shows glucosamine, titration shows 15.0–17.0% sulfate, and potassium and chloride are present in the proportion the complex requires. The assay alone cannot separate the 2KCl complex from the hydrochloride, the sodium form or a dilution.

In one line

A sulfate lot is proven by three agreeing numbers: the glucosamine assay, the sulfate titration and the potassium or sodium that belongs to the counter-ion.

The four identity layers

Paperwork can name the right material without proving it. The four layers below ask separate questions, and each needs its own evidence; a supplier who answers only the first has described the label, not the powder.

Four layers of glucosamine sulfate 2KCl identity
LayerQuestionTestWhat it proves
DocumentIs the form named?Name, CAS number, formulaPaperwork only
ChromatographyIs the amino sugar glucosamine?HPLC retention against a glucosamine standardThe molecule
SulfateIs the counter-ion sulfate?Titration, 15.0–17.0%The 2:1 salt
Counter-ion and balanceIs the solid the 2KCl complex?Potassium by ICP-OES, chloride by titration, loss on dryingThe complex and any dilution

The sulfate ratio and the mass balance

At full stoichiometry the 2KCl complex is 15.9% sulfate, 12.9% potassium and 11.7% chloride; the glucosamine base is 59.2%. The catalog sulfate range of 15.0–17.0% brackets the theoretical value, so the ratio is a direct check on the form rather than a generic purity figure.

Read the sulfate against the assay. A 100% assay with 15.9% sulfate is consistent with the complex. A 100% assay with 13% sulfate is not; the missing sulfate has to be replaced by something. A high sulfate with a normal assay points to an added sulfate salt, which lifts the mineral load without lifting glucosamine. A high potassium with a low assay points to added potassium chloride. The numbers constrain one another, and that is the point of reporting all of them.

The ratio also catches a blend that the assay cannot. A blend of the 2KCl complex and the hydrochloride can be adjusted to land inside the assay range, but its sulfate falls and its chloride rises. A blend with the sodium form shows sodium where potassium should be. The assay sees the amino sugar; the counter-ion sees the form.

X-ray diffraction and the solid state

X-ray diffraction answers a different question: is the solid crystalline, and does its pattern match a reference? The 2KCl complex is a crystalline solid, and a dilution with an amorphous carrier changes the pattern. The method can compare lots from two sources and can distinguish a crystalline complex from a spray-dried solid or an amorphous carrier blend.

Potassium chloride is crystalline too, so strong alkali-halide lines beside a weak glucosamine pattern deserve a question. Before accepting a “match”, ask for the reference pattern and the detection limit. XRD is not a routine release test here, and “XRD conforms” without the pattern adds little.

What adulteration looks like

Common substitutions and the signals
SubstitutionWhat it doesSignalTest
HydrochlorideRaises base per gram; no sulfateChloride high, sulfate lowChloride and sulfate titration
Sodium formReplaces potassium with sodiumSodium present, potassium lowICP-OES for potassium and sodium
DilutionLowers assay and sulfate togetherAssay low, sulfate low, loss on drying may riseMass balance, loss on drying
Added sulfate or KClLifts the sulfate or potassium lineSulfate or potassium high with a normal assaySulfate, potassium and assay together
MoistureLowers the as-is assayLoss on drying high; dried-basis assay normalLoss on drying, both assay bases

Colour is the weakest signal. White to off-white covers a range, and a yellow cast can come from moisture or heat rather than from a different material. The stronger signals are the sulfate, the potassium and the mass balance.

How to write identity into the specification

  • “Glucosamine sulfate 2KCl, CAS 14999-43-0, (C6H13NO5)2·H2SO4·2KCl.”
  • “Assay 98.0–102.0% by HPLC; state the basis on the certificate.”
  • “Sulfate 15.0–17.0% by titration.”
  • “Loss on drying ≤1.0%; particle size ≥95% through 80 mesh.”
  • “Potassium about 12.9% and chloride about 11.7%, where the counter-ion is to be confirmed.”
  • “No hydrochloride substitution: the sulfate figure must stay within 15.0–17.0%.”
  • “Source (shellfish or fermentation) and the matching allergen statement.”

Five questions for the supplier

  1. Which salt form is this lot, and which CAS number is on the certificate?
  2. Can you provide the HPLC chromatogram and the standard used, not only the assay percentage?
  3. What is the sulfate result, and which titration method produced it?
  4. What are the potassium and chloride results for this lot?
  5. What is the source, and what allergen statement accompanies it?

Five answers of this kind make an identity file; one assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits; the grades page compares the forms; the compliance page covers source and allergen; the HPLC note explains the separation.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation