02 Grade comparison

Creatine HCl powder or granulated: choosing a physical grade

Technical document 02 · Reviewed 2026-11-20 · Creatine HCl

On this page
  1. Why a single salt still has a grade decision
  2. The two catalogued grades
  3. Flow, bulk density and the moisture barrier
  4. What the grade does in a capsule, tablet or stick
  5. What to write into a grade specification
  6. When not to change grade

Creatine hydrochloride is supplied as an 80 mesh powder, with a granulated version on request. Both carry the same chemical specification — assay 99.0–101.0% as the salt, creatine 74.0–78.0%, chloride near 21.2% and loss on drying ≤1.0% — while the particle-size line changes with the grade. The decision is about flow, dust, bulk density and fill, not a second purity level.

In one line

The grade changes how the powder flows and fills; the hydrochloride identity, assay and creatine content stay the same.

Why a single salt still has a grade decision

Creatine hydrochloride has one identity: the 1:1 salt of creatine with hydrogen chloride, CAS 17050-09-8. There is no hydrate choice to make, as there is with creatine monohydrate. What the buyer can choose is the physical form: the standard 80 mesh powder or a granulated material made from it.

That is a processing choice. Milling and sieving set the particle-size distribution; granulation builds larger, denser particles from the fine powder. Neither step changes the assay, the creatine content, the chloride or the loss-on-drying limit. A specification that describes “granulated” as a purity grade has confused the powder with the chemistry.

The form question is separate. Creatine monohydrate is a different product with a different CAS number, molecular weight and creatine content; the monohydrate page covers that choice. This page covers the physical grade; the level-four comparison covers the form.

The two catalogued grades

Physical grades of creatine hydrochloride
Property80 mesh powderGranulated, on request
DescriptionWhite to off-white, free-flowing powderAgglomerated or compacted granules from the same powder
Particle size≥95% through 80 meshGranule cut agreed with the buyer; fines content stated
FlowGood for a fine powder; can bridge in a narrow hopperUsually freer and more uniform in a hopper or feeder
DustHigher; needs extraction at the filling headLower; less powder on seals and surfaces
WettingFast; disperses with stirringSlower; granules must break down before they dissolve
Bulk densityLower and more variable with finesHigher and more consistent
Typical fitStick packs, drink mixes, dry blends, small capsule runsHigh-speed capsules, tablets, blends that segregate
What to confirmSieve standard and percentage passingGranule cut, fines, binder or water-only process

The granulated grade is not automatically the better one. It buys flow and dust control at the cost of a slower wetting step, and it adds a processing operation that has to be specified and sampled. The powder is the simpler choice when the line can handle a fine, static-prone material.

Flow, bulk density and the moisture barrier

Flow is the first property the line notices. An 80 mesh hydrochloride powder is fine and slightly hygroscopic; in a humid room it can pick up water, cake at the surface and bridge in a hopper. Granulation reduces the surface area per gram and usually improves flow, but it does not make the salt non-hygroscopic. The pack and the room still decide how much water the powder meets.

Bulk density follows the same pattern. A fine powder traps more air and fills a capsule by volume with less mass; a granulated powder packs more densely and gives a more consistent fill. That matters more for the hydrochloride than for the monohydrate, because a gram of hydrochloride carries less creatine. A low bulk density and a low creatine fraction compound the fill problem.

The acid is a separate handling point. The powder dissolves to an acidic solution, and the dry dust is irritating to the eyes and airways in the same way as other fine acidic salts. Local exhaust, eye protection and a clean filling head belong in the handling plan. Granulation lowers the dust but does not remove the acidity from the solution.

What the grade does in a capsule, tablet or stick

A capsule fills by volume, so bulk density and powder volume decide the fill before the label does. A 500 mg fill of hydrochloride at 78% creatine delivers about 390 mg of creatine; the same fill of monohydrate delivers about 440 mg. A formulator matching a creatine dose therefore needs more hydrochloride mass, and a granulated grade can help fit that mass into a consistent fill without weight variation.

In a tablet, the granulated grade is usually the easier starting point: it flows into the die, resists segregation from fine excipients and compacts more evenly. The acidic salt can also interact with acid-sensitive excipients or coatings, so the formulation check is not only a flow check. Direct compression is the simpler route; a wet granulation step adds water and heat, which is the condition the salt is least suited to.

For a stick pack or drink mix, the 80 mesh powder is the usual choice because it wets quickly. The granulated grade may need more stirring and can leave a gritter mouthfeel if the granules do not break down. Test the actual drink at the target pH and temperature, not only the powder in a beaker. A grade that disperses well in water can still fail in an acidic, warm matrix.

What to write into a grade specification

  • “Creatine hydrochloride, CAS 17050-09-8, C4H9N3O2·HCl; single salt, no monohydrate or diluent.”
  • “Assay 99.0–101.0% as the salt by HPLC; creatine content 74.0–78.0%; chloride by titration.”
  • “Loss on drying ≤1.0%; heavy metals and microbiology as catalogued.”
  • “80 mesh powder: ≥95% through 80 mesh, sieve standard named.”
  • “Granulated: granule cut and fines content agreed; method (water-only or binder) declared.”
  • “Bulk density target and flow test agreed where the filling line depends on them.”

The chemical block should not change when the grade changes. If a granulated offer carries a different assay, creatine content or loss-on-drying limit, it is a different specification, not the same product in a coarser form. Ask for the granulation method and any processing aid, because a binder is an added ingredient and belongs on the documentation.

When not to change grade

If the powder runs on the line, meets the fill target and disperses as the finished product needs, a grade change adds a processing step and a new qualification without improving the product. A finer or granulated powder does not raise the creatine content, make the solution less acidic or turn the salt into the monohydrate. If the problem is caking, creatinine or a pH shift, the answer is in the pack, the storage or the formula, not the sieve.

The catalog specification sits on the creatine HCl product page. The level-four comparison sets the hydrochloride against the monohydrate; the COA page shows where the grade sits on the certificate; the stability page covers moisture and acid. The methods section explains the sieve and titration work, and the quality page describes release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation