06 Identity & adulteration

How to prove a citicoline lot is the named form

Technical document 06 · Reviewed 2026-11-19 · Citicoline

On this page
  1. Four checks, four questions
  2. The sodium and phosphorus ratios
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Questions to put to the supplier

The certificate proves the form only when the HPLC retention and UV spectrum, the sodium result, the water figure and the assay tell the same story. A percentage on its own cannot tell the free acid from the sodium salt, and it cannot tell either one from a diluted powder. Ask for the chromatogram, the counter-ion result and the moisture basis before accepting the name on the label.

In one line

The assay measures the nucleotide; the sodium figure identifies the salt, and the water result shows how much of the powder is dry matter.

Four checks, four questions

The four checks below are independent. A supplier who provides only the first has repeated the label, not demonstrated the lot.

Four checks of citicoline identity
LayerQuestionTestWhat it proves
DocumentIs the form named?Name, CAS number, formulaPaperwork only
ChromatographyIs the nucleotide citicoline?HPLC retention and UV spectrumThe molecule, not the form
Counter-ionIs it the free acid or the sodium salt?Sodium by ICP-OESThe salt form
Mass balanceIs it diluted or wet?Assay, water, related substancesConsistency of the numbers

The sodium and phosphorus ratios

Citicoline sodium is a monosodium salt, so its theoretical sodium content is 22.99 ÷ 510.31 = 4.50%. The free acid contains none. A sodium figure near 4.5%, with an assay in range, supports the salt; a low figure points to the free acid or a dilution; a high figure suggests another sodium source. Sodium is not a catalog parameter, so it is an extra test, ordered when the form is disputed or a new source is qualified.

Phosphorus adds a second check. Citicoline has two phosphorus atoms per molecule: 12.69% by mass in the free acid and 12.14% in the sodium salt. A figure near the theoretical value supports the diphosphate; a low figure next to a clean UV peak suggests a less phosphorylated nucleotide, or a dilution. Choline is a third check, at about 21.3% of the free acid and 20.4% of the salt. The molecule should show two phosphorus atoms for every choline group.

A blended powder can also be built to sit inside the assay range. Its sodium figure will land between zero and 4.5% according to the salt fraction; the assay measures all of the citicoline, while the sodium figure measures only the salt fraction.

X-ray diffraction: the solid-state check

XRD looks at the solid state: whether the powder is crystalline, partly crystalline or amorphous, and whether the pattern matches a reference. A change here can alter bulk density, flow and dissolution even when the assay stays put, which matters when a capsule line has been validated on one powder and a later lot flows differently.

XRD does not measure purity or the counter-ion, and it is not a routine release test. Before accepting a “match”, request the reference diffractogram and the method's detection limit. “XRD conforms” on its own, with no pattern and no reference, tells the reader almost nothing.

What adulteration looks like

Common citicoline substitutions and the signals
AdulterantWhat it doesSignalTest
Choline chloride or bitartrateCheap choline source with no cytidineLow phosphorus; no nucleotide peak; high cholineHPLC-UV, phosphorus, choline
Cytidine monophosphate or cytidineSimilar UV chromophore, fewer or no phosphatesLow phosphorus and low choline; different retentionHPLC-UV, phosphorus, choline
Dilution with a sugar or carrierLowers assay; changes water and flowAssay low; water or ash highMass balance, HPLC
Wrong citicoline formFree acid sold as salt, or the reverseSodium off 4.5% or near zero; pH shiftSodium by ICP-OES, pH
WaterLowers the as-is assay; cakes the powderWater high; anhydrous assay normalKarl Fischer

Appearance is the weakest signal: both forms are white powders, and a diluent can match the colour. The sodium figure, the phosphorus and choline ratios and the mass balance carry more weight. A certificate with appearance and assay but no identity evidence has not tested the substitution that matters most.

How to write identity into the specification

  • “Citicoline free acid, CAS 987-78-0, C14H26N4O11P2.”
  • “Assay 98.0–102.0% by HPLC with UV detection; state the moisture basis and the reference standard.”
  • “Identification by HPLC retention and UV spectrum against the citicoline reference.”
  • “Water ≤5.0% by Karl Fischer; pH of a 5% solution 2.5–4.5.”
  • “Sodium about 4.5% by ICP-OES where the sodium salt is claimed; report phosphorus where the nucleotide is in question.”
  • “No unrelated nucleotide above the agreed limit; state the limit and the method.”
  • “The destination and the form are settled before the purchase order.”

Questions to put to the supplier

  1. Does the certificate name the free acid or the sodium salt, and with which CAS number?
  2. Will you send the chromatogram and the UV spectrum, not just the assay figure?
  3. What sodium figure did ICP-OES give, and on which sample?
  4. How was the assay basis calculated, and what water result goes with it?
  5. If the result is disputed, will you re-test the retained sample jointly?

Those five answers, taken together, are the identity file; one assay percentage is not. Start with the citicoline product page for the catalog limits. The COA page explains how a lot is released; the grades page sets out the form choice; the level-four page follows the label arithmetic; the HPLC note describes the separation.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation