03 Stability & pack

Beta-glucan stability: moisture, heat and the pack

Technical document 03 · Reviewed 2026-11-19 · Beta-Glucan

On this page
  1. The powder: water, lumps and colour
  2. A dispersion, not a solution
  3. What changes during storage
  4. Designing the stability trial
  5. Capsules, sticks and drinks
  6. Where the retest period comes from

Dry yeast β-glucan shows little chemical loss in storage; the changes that matter are moisture uptake, caking, colour drift and, in a liquid, viscosity loss and microbial growth. The sealed pack limits the first three, and the process controls the last two. A shelf life is a property of the pack and the storage condition, not of the polymer alone.

In one line

Dry β-glucan is chemically patient; the pack has to keep it dry, sealed and clean, and any liquid format needs its own stability work.

The powder: water, lumps and colour

The catalog moisture limit is ≤6.0%. That is a release gate, not a licence to leave the pouch open. Once air reaches the powder, moisture climbs, the as-is β-glucan percentage falls by dilution, and the particles can fuse into lumps that disperse poorly. A folded-over foil pouch is not a seal; a heat-sealed pack that has been cut open should be closed with a proper clip or transferred to a smaller dry container.

Colour moves more slowly than moisture, and it is not a reliable assay. The off-white to light brown range covers normal variation, so a small shade change is not a failure. A clearly darker powder can reflect a hot dryer, a long hold, or a reaction between the protein fraction and residual sugars. When colour changes, re-check moisture and β-glucan before deciding whether the lot is still usable.

Ordinary warehouse temperatures are tolerable for a sealed pack; a hot loading bay, a car in summer or a leaking roof is not. If a pack has been cold, let it reach room temperature before opening so that condensation does not form on the powder.

A dispersion, not a solution

In water the powder disperses into a suspension, and at higher solids it becomes viscous. That viscosity is a functional property, not a purity reading: it depends on concentration, particle size, shear history and temperature. Measure it at a fixed solids level if it is going to be a specification, otherwise two results cannot be compared.

Water also makes the product a microbial substrate. An unpreserved dispersion can support bacteria, yeasts and moulds, and a pasteurisation or hot-fill step reduces the load while adding heat. The preservative system, the pH and the hold time before filling all need validation in the finished matrix. A clean powder COA does not make a liquid stable.

A beverage trial should use the real process, not a bench stir. The heat load, the pump shear, the fill temperature and the pack all influence viscosity and microbial outcome. The yeast versus oat comparison explains why an oat concentrate thickens at lower solids and why the two sources cannot be swapped in a drink without rebuilding the trial.

What changes during storage

Storage variables for yeast β-glucan
VariableEffectControl
WaterDilutes the as-is assay; causes caking and clumpingSealed pack, dry room, closed liner
TemperatureSpeeds colour change and moisture movementAmbient store away from hot surfaces
MicrobesMultiply in a wet powder or an unpreserved liquidDry pack; validated preservation and heat step
ShearReduces viscosity in a dispersionSet pump and homogeniser conditions
pHCan degrade the polymer at extremesValidate matrix pH and hold time
Pack damageA pinhole admits water vapour and airInspect seams; store off the floor

The variables reinforce one another. A humid store plus a damaged liner is worse than either alone, and a warm, acidic drink combines chemical and microbial risk. The productive question is not whether the polymer is stable in principle, but how long this pack keeps this specification under this storage condition.

Designing the stability trial

Before the first sample enters the chamber, settle four points: which pack is being tested, where it will be stored, when it will be pulled, and what will be measured. A common design uses a warehouse arm at 25 °C and 60% relative humidity, an intermediate arm at 30 °C and 65% relative humidity, and an accelerated arm at 40 °C and 75% relative humidity. Clear jars, tropical destinations or a retort step need an arm that those chambers do not supply.

At each point, test β-glucan by the named enzymatic procedure, moisture, ash, protein, appearance and microbiology. If the material is sold as a dispersion, add viscosity at a fixed solids level. Report the individual values rather than a single pass statement; a trend is more useful than a verdict, and the report should name the pack and the lot family.

Order the study on the commercial pack. Headspace, exposed surface and opening frequency are not the same for a 1 kg pouch and a 25 kg drum, so data from one cannot be read across to the other.

Capsules, sticks and drinks

Capsule shells and tablet excipients are not perfectly dry, and water can migrate into the fill during storage. Release and end-of-storage moisture results, plus a visual check for caking, are the minimum. In a stick pack the seal is an additional failure point: inspect the strip for pinholes, not only the powder inside.

A drink adds water, pH, heat and microbial risk. The bulk ingredient's stability is only the starting point. An overage may be a legitimate label decision, but it does not compensate for a pack that leaks or a process that leaves the drink unpreserved.

Where the retest period comes from

There is no single shelf-life figure for β-glucan. The retest period is written against a named pack and a named storage condition, and the file behind it has to show the test panel and the time points. Strip away the pack and the condition and what remains is a claim, not a shelf life.

When the retest period expires, test the retained sample again before extending it. An extension needs a result; a drum's history cannot be transferred to a pouch that was repacked later. Pack options are listed on the beta-glucan hub; release tests are on the COA page; ordering details sit on the MOQ page; the methods library explains the assays; the quality page describes how a lot is released. A parallel polymer file is on the chitosan page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation