06 Identity & adulteration

How we prove a beta-glucan lot is yeast 1,3/1,6-glucan

Technical document 06 · Reviewed 2026-11-19 · Beta-Glucan

On this page
  1. The four identity layers
  2. The 1,3 to 1,6 linkage ratio
  3. X-ray diffraction: what it can and cannot show
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Five questions for the supplier

A β-glucan lot is yeast 1,3/1,6-glucan when four things agree: the source record names the yeast and the cell-wall process, the enzymatic assay reports β-glucan by a named method, the sugar and linkage profile is consistent with a 1,3/1,6 polymer, and the mass balance leaves no room for a carrier. The assay alone cannot separate yeast from oat, because both are glucose polymers.

In one line

Identity is source plus linkage plus method: the assay measures glucose, while the source record and the linkage pattern say which β-glucan it is.

The four identity layers

A correct name on the certificate does not prove the powder. Each layer below answers a different question, and each needs its own evidence; an answer that stops at the first layer describes paperwork rather than material.

Four layers of yeast β-1,3/1,6-glucan identity
LayerQuestionEvidenceWhat it proves
DocumentAre the source and linkage named?Name, CAS 9041-22-9, yeast strain, specificationPaperwork only
AssayHow much β-glucan is present?Named enzymatic method, with the basisThe β-glucan figure
StructureIs it a 1,3/1,6 polymer?Sugar profile, linkage analysis, spectroscopyThe linkage family
Mass balanceIs it diluted or extended?Moisture, ash, protein, sugar profileConsistency of the numbers

The 1,3 to 1,6 linkage ratio

Yeast β-glucan has a β-1,3-linked backbone with β-1,6-linked branches. The ratio of the two linkage types is a structural descriptor: it varies with the yeast fraction, the extraction and the analytical method, and it is not a fixed label claim. The catalog specification names the linkage family; a lot-specific ratio is an additional structural test, not a routine release line.

The enzymatic assay does not report that ratio. It hydrolyses β-linked glucan to glucose and reports the total, so a yeast 1,3/1,6 polymer and an oat 1,3/1,4 polymer can both produce a glucose figure under a suitable enzyme set. Linkage analysis by methylation and gas chromatography, or by NMR, is what separates the families. Those methods are slower and more expensive than the release assay, and they are used to qualify a source or settle a dispute rather than to release every lot.

HPLC is a third view. A monosaccharide profile after hydrolysis confirms that glucose is the constituent sugar; a size-exclusion method gives a molecular-weight distribution. Neither is a source test on its own. A certificate that reports “HPLC conforms” without saying what the HPLC measured has added a word, not a result.

X-ray diffraction: what it can and cannot show

β-Glucan is largely amorphous, so its X-ray diffraction pattern is broad rather than a set of sharp reflections. XRD cannot identify the yeast source, and it cannot measure the β-glucan content. It can show that a crystalline phase is present, which is useful when a carrier such as dextrose, sucrose, lactose or a mineral filler is suspected, and it can compare the solid form of two lots.

XRD is not a routine release test for this product. Request the reference pattern and the detection limit before accepting a statement that the pattern matches, and read a positive crystalline phase as a question about the formulation rather than a verdict on the β-glucan. The XRD method note describes the instrument and the sample preparation.

What adulteration looks like

Common β-glucan substitutions and the signals
SubstituteEffectWarning signCheck
Maltodextrin or glucoseRaises bulk without adding β-glucanβ-glucan below expectation; extra glucose in the profileEnzymatic assay plus HPLC sugar profile
Oat or mushroom β-glucanSupplies glucose under the same nameSource record inconsistent; linkage pattern differsLinkage analysis and source audit
Celluloseβ-1,4 glucan used as bulkInsoluble residue; recovery changesLinkage analysis and microscopy
Starchα-glucan, outside the β-glucan definitionα-glucan fraction highSeparate α-glucan digestion
Protein or ash fillerAdds mass; shifts the balanceProtein or ash over the limitNitrogen determination and ashing
MoistureLowers the as-is resultMoisture high; dry-basis figure normalLoss on drying

Colour is the weakest signal. Off-white to light brown covers a wide range, and a blend can reproduce it. The stronger signals are the method, the sugar profile, the linkage pattern and the mass balance.

How to write the identity into the specification

  • “Yeast-derived β-1,3/1,6-glucan, CAS 9041-22-9, (C6H10O5)n, from Saccharomyces cerevisiae.”
  • “β-Glucan ≥70% by the named enzymatic method; state the basis.”
  • “Moisture ≤6.0%; ash ≤3.0%; protein ≤5.0%.”
  • “Identification by enzymatic and HPLC methods conforming to the reference.”
  • “No added maltodextrin, glucose or other carrier unless declared and quantified.”
  • “Source, strain and cell-wall process under change control.”

Five questions for the supplier

  1. Which yeast and which cell-wall process produced this lot?
  2. Which enzymatic method and which kit were used, and is the result as-is or dry basis?
  3. Can you provide the chromatogram or sugar profile behind the HPLC identification?
  4. What are the moisture, ash and protein results for this lot, and how do they close the mass balance?
  5. If the source or the linkage is disputed, will you agree to a joint re-test of the retained sample?

Those five answers, taken together, form an identity file; one assay percentage does not. Catalog figures are on the beta-glucan hub; the COA page locates each result on the certificate; the grades page compares the source families; the level-four comparison follows the linkage and claim consequences; the chitosan page is a parallel case for a source-dependent polymer; the methods library explains the procedures; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation