What the COA for 5-HTP actually contains
This page lists what a 5-HTP certificate is expected to report: appearance, IR and UV identification, HPLC assay on the dried basis, loss on drying, residue on ignition, related substances, metals, microbiology and particle size. Each entry needs a method and a release limit, not only a value. The ranges here are catalog limits; only the batch COA can speak for a specific drum.
The assay says how much 5-HTP the lot contains; the drying basis, the related-substance profile and the source say what that number means.
Reading the certificate line by line
The identity and purity block carries most of the weight. A 5-HTP figure is meaningful only when the material has been identified, the moisture has been measured and the rest of the chromatogram has been described.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | Off-white to pale cream crystalline powder |
| Identification | IR and UV against reference | Conforms |
| Assay | HPLC, external standard | 98.0–101.0% on the dried basis |
| Loss on drying | Gravimetric | ≤0.5% |
| Residue on ignition | Gravimetric | ≤0.1% |
| Parameter | Method | Release limit |
|---|---|---|
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Particle size | Sieve analysis | ≥95% through 40 mesh |
| Related substances | HPLC | Individual and total limits agreed in the specification |
The related-substance entry deserves its own line. “Complies” is not a result: the buyer needs the individual peaks, their sum, the column and detector, and the quantification limit. Without the individual figures, one large impurity and six small ones look identical.
What the dried basis changes
5-HTP is released against an assay calculated after the moisture result is removed. Divide the as-is figure by (1 − loss on drying). At the catalog ceiling of 0.5% the correction is only about half a percent, but a certificate that omits the basis cannot be compared with one that states it.
An assay above 100% is not a purity above 100%. The number is relative to a reference standard; weighing, standard purity and integration each contribute. A 100.4% result is within normal method behaviour, not evidence of extra material.
Read the assay beside the other three lines. Related substances describe the rest of the chromatogram, loss on drying covers water, and residue covers inorganic matter. Together they should close the mass balance; a large unexplained gap is a reason to ask, not to release.
The limit and the measured result
Two different numbers are often printed in one column. The limit is the gate; the result is the measurement. They should be separate, and the method should sit beside them. Copying the range into the result column defeats the purpose of a certificate.
Some tests are attributes: identification conforms or does not, and a pathogen is absent or present. Others need an individual and a total. A “not detected” statement is only as useful as the detection limit printed next to it.
Release is a judgement made from the figures, not a stamp that replaces them.
What moves between batches
Between extract lots, harvest timing, solvent, purification and drying change colour, moisture and the impurity pattern. Between synthetic lots, the starting material, the chiral step and the recrystallisation solvent move the same lines differently. The assay can remain inside 98.0–101.0% while the rest of the profile shifts, so the certificate is read as a pattern, not a headline.
Milling and sieving set the particle-size result, and flow can differ between two lots that both pass 40 mesh. Colour is a useful warning: cream turning tan or pink can signal oxidation or a metal trace even when the assay is on target. Check the batch record before rejecting a lot on appearance.
Look at the direction across several lots. One result at the edge is less telling than moisture creeping up or total impurities trending higher.
When an outside test earns its place
Outside testing is worth ordering for a new source, a first import into a regulated market, a source claim that the certificate cannot support, or a contested result. A focused panel is enough: HPLC assay with related substances, IR and UV, optical rotation where chirality matters, ICP-MS for metals and a micro count, all from one sample.
Provenance is the limit. A 98% extract and a 98% synthetic lot look the same to the assay; only the manufacturer's declaration and the lot record address the route. A laboratory can confirm what the material is, not where it came from.
Keep the chain intact: the sample that is tested should be the sample that was retained, and its lot code should match the certificate and the pack.
Comparing two suppliers
Six lines separate two offers: source and manufacturer; assay with its method and basis; individual and total related substances with the quantification limit; loss on drying; the metal and micro panel; and the pack. An assay match that leaves the other five different is not a match on material.
Traceability is the second layer. One lot code should run through certificate, drum and retained sample, and the manufacturer should be named rather than a trading intermediary. A genuine certificate can still describe a different drum from the one that arrives.
The catalog range and pack are on the 5-HTP product page. Source selection is covered on the source page, identity testing on the identity page, the release sequence on the quality page, and the HPLC method in the method note.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation