What the COA for whey protein concentrate actually contains
A certificate for whey protein concentrate carries one figure that carries most of the weight and explains itself least: the protein content. It is a nitrogen measurement, multiplied by a conversion factor and expressed against a moisture basis, and each of those choices moves the number. Around it sit the limits that describe the rest of the powder — lactose, fat, ash, moisture, pH, particle size and contaminants. The catalogue sets the limits; the batch COA confirms the lot.
A whey certificate is read backwards: the protein figure means nothing until the nitrogen factor and the dry basis are named, and the lactose, fat and ash limits describe what the powder actually is.
The parameter list
Whey protein concentrate has no CAS number: it is a mixture of proteins, peptides, lactose, fat and minerals, not a single molecule. The certificate is built from the parameters that describe that mixture. The table below is the catalogue parameter list for the WPC 80 grade.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White to light cream powder |
| Protein (dry basis) | Kjeldahl, N × 6.38 | ≥80.0% |
| Moisture | Loss on drying | ≤5.0% |
| Ash | Gravimetric, furnace | ≤4.0% |
| Fat | Solvent extraction | ≤6.0% |
| Lactose | HPLC | ≤5.0% |
| pH (5% solution) | Potentiometry | 6.5–7.5 |
| Particle size | Sieve analysis | ≥95% through 80 mesh |
| Parameter | Method | Release limit |
|---|---|---|
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and enrichment | APC ≤10,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent |
The grade name belongs on the certificate, not only in the covering email. “Whey protein concentrate” without the 80 is a family name, and the lactose and fat limits differ across the family. The grade comparison sets out how far apart two members of that family can be.
What the protein figure is measured against
Kjeldahl digests the sample and measures the nitrogen released, not the protein. The result is multiplied by a conversion factor. For milk proteins the convention is 6.38, which assumes that nitrogen is about 15.7% of the protein mass. An 80.0% figure therefore corresponds to roughly 12.5% nitrogen, and a laboratory using a different factor will report different protein for the same digest.
The basis is the second half of the same problem. This catalogue states its figure on a dry basis, which means the moisture is divided out before the calculation. At the 5.0% moisture limit, an 80.0% dry-basis figure corresponds to 76.0% as-is; a specification that does not name the basis can be met by a material four points different from the one intended. A certificate reporting 78.4% is not a weaker lot either — that is what the same nitrogen result gives under the general food factor of 6.25.
Three things have to travel together: the protein value, the factor and the basis. A purchase order that copies a percentage without them has copied a conclusion and left the evidence behind.
Catalogue range, release limit and lot result
A release limit defines the window a lot has to sit inside; a lot result is what the bench actually measured on that lot. Both belong on the certificate, against the method, because “conforms to specification” on its own is a verdict with no figures attached to it. Where the limit is a ceiling, lead at 2.9 mg/kg and lead at 0.5 mg/kg both pass the same line, and they are not the same risk in a product dosed at 30 g a day.
Some parameters are reported rather than limited. Particle size is the clearest case: the specification requires at least 95% through 80 mesh, and the certificate can still report the measured distribution. A lot can pass the cut-off at the coarse edge of the distribution, and the difference shows up in wetting and flow.
What this page describes is a catalogue specification: the level the material is expected to meet. The batch COA confirms the lot that ships, and this site does not publish batch results, batch numbers or customer names.
What moves between lots
The protein and lactose figures follow the whey that went in. Sweet whey from rennet-coagulated cheese and acid whey from casein manufacture are different starting materials, with different ash, calcium and lactose, and a plant that switches source will see the ash figure move before the protein does. Season and stage of lactation move the protein-to-lactose ratio in the milk itself, which is why a specification with a protein floor and no lactose ceiling is easier to meet on paper than in a drum.
The separation step is the next lever. Ultrafiltration and diafiltration decide how much lactose and ash are washed out, and the membrane cut-off decides which peptides stay. Drying then sets the moisture, the particle size and part of the colour: a hotter inlet can push the powder from white towards cream and lower its solubility while the protein figure stays where it was.
Colour and odour are the least quantitative signals and often the most useful. WPC 80 can pick up a cooked or cardboard note after a hot drying run, and the same note strengthens with moisture uptake in storage. That is a reason to ask for a retained sample and a storage history, not a reason to reject the lot on the protein figure alone.
When to involve an outside laboratory
Send a sample out when the whey source is unfamiliar, when a first shipment is heading into a regulated market, or when the label carries a statement the certificate does not prove. The useful panel answers the open question rather than repeating the certificate: the amino acid profile to check that the nitrogen is protein nitrogen, lactose by HPLC to confirm the grade, melamine and other non-protein nitrogen by LC-MS/MS where that risk exists, and the contaminant panel by ICP-MS on the same sample. A milk protein ELISA on the finished product answers the allergen question the raw-material COA cannot.
The six lines to compare
Six lines decide whether two offers describe the same powder: the protein figure with its factor and basis, the lactose limit, the fat and ash limits, the moisture limit, the allergen statement, and the microbiological limits. Two quotations that agree on 80% protein and disagree on the other five are not quoting the same material.
Behind the paper sits the record: which plant ran the lot, which whey source went in, which membrane and drying conditions were used, and what retained sample exists. Accurate paper can still describe a different lot from the one in the truck, so the number on the COA, the drum and the retained sample should be one number.
For the full range behind these limits, see the whey protein concentrate product page. The definition of the certificate is in the COA glossary entry, the moisture method is covered by loss on drying, and the file itself is described on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation