WPC 80 or WPI 90: choosing a whey protein grade
Whey protein concentrate 80 and whey protein isolate 90 are the same starting material separated to different degrees. The grade fixes the protein floor, the lactose and fat that come with it, and the way the powder behaves in a drink or a bar. The protein percentage is the headline; the lactose, the fat and the physical form are the part that decides whether the grade fits the product. This page covers the choice between grades; the arithmetic behind the two numbers is set out on WPC 80 versus WPI 90.
The grade is the protein-to-lactose ratio and the physical form behind it, not the protein number on its own.
Why one name covers several materials
Whey is the liquid left after milk is coagulated for cheese or casein. Drying it whole gives whey powder, which is mostly lactose. Concentrating the protein by ultrafiltration and washing out lactose and ash gives whey protein concentrate, and the concentration step decides whether the result is a 35, a 50 or an 80. Removing more of the non-protein fraction — by ion exchange, by microfiltration, or by a combination — gives whey protein isolate at 90 or above.
The grade is therefore a specification, not a brand. Two suppliers can both offer “WPC 80” and differ in lactose, fat, ash, particle size and how the powder was dried. A label that says “whey protein” without the grade is a family name, and the buyer is entitled to ask which member of the family is in the drum.
The grades side by side
| Point | WPC 80 | WPI 90 |
|---|---|---|
| Protein, dry basis | ≥80.0% (N × 6.38) | ≥90.0% (N × 6.38) |
| Protein, as-is at 5% moisture | 76.0% | 85.5% |
| Lactose | ≤5.0% | Typically ≤1.0% |
| Fat | ≤6.0% | Typically ≤1.0% |
| Ash | ≤4.0% | Process-dependent |
| Separation | Ultrafiltration and diafiltration | Ion exchange or microfiltration |
| In water | Opaque, foams on mixing | Clearer, lower foam |
| Usual fit | Bars, powder blends, opaque drinks | Clear drinks, low-lactose formulas |
The two rows that matter for most formulas are lactose and fat, not protein. A WPC 80 at its 5% ceiling carries five times the lactose of a WPI 90 held to 1%, and the gap widens per gram of protein delivered because the isolate needs less powder to reach the same dose.
What changes in the drum
Both grades are spray-dried powders, and both can be agglomerated or instantized on request. Agglomeration builds larger, porous particles that wet faster and make less dust; it also lowers bulk density and changes how the powder fills a sachet. The WPC 80 catalogue requires at least 95% through 80 mesh, and an isolate is usually specified the same way, but the measured distribution and the flow behaviour can differ between suppliers and between drying runs.
WPC 80 is the more hygroscopic of the two in practice, because the lactose it carries is what takes up water first. In a warm filling room that shows up as sticking on the hopper, lumps in the bag and a powder that no longer flows. WPI 90 has less of that lactose, but it is not exempt: protein itself is hygroscopic, and a fine isolate can cake as firmly as a concentrate once moisture is above the limit.
Foam is the other physical difference a formulator notices. A WPC 80 solution foams readily when mixed or pumped, which is welcome in some aerated products and a nuisance in a filling line that needs a still surface. WPI 90 foams less, and the difference is large enough to change the process rather than the recipe.
What changes in the finished product
Dose arithmetic uses the as-is protein figure, not the dry-basis one. To deliver 20 g of protein from a WPC 80 at the 5% moisture limit, the formula needs 20 ÷ 0.76 = 26.3 g of powder. The same 20 g from a WPI 90 needs 20 ÷ 0.855 = 23.4 g. The difference is about 3 g of powder per serving, and it is the powder — with its lactose, fat and ash — that the rest of the formula has to absorb.
At those weights, the WPC 80 serving carries at most 1.3 g of lactose and 1.6 g of fat; the WPI 90 serving carries at most 0.23 g of lactose and 0.23 g of fat. For a bar or a flavoured shake those are small numbers. For a clear drink, a lactose ceiling or a very tight carbohydrate declaration they are the numbers that decide the grade.
Scoop size follows the same arithmetic. A 25 g scoop of WPC 80 at 76.0% protein delivers 19.0 g, not 20 g. A label that rounds the powder weight instead of the protein will be wrong on the panel, and a serving that is meant to hit a protein claim has to be built from the as-is figure every time.
What to put in the specification
- The grade and the process: whey protein concentrate 80, spray-dried, with agglomeration or instantizing named if required.
- Protein with its nitrogen factor and basis: ≥80.0% dry basis by Kjeldahl, N × 6.38.
- Lactose, fat, ash and moisture as limits, not as typical values, because these are the parameters that separate one supplier's 80 from another's.
- Particle size and the test method, since 80 mesh by sieve and 80 mesh by laser diffraction are not the same measurement.
- The allergen statement and the milk declaration, because both grades carry milk protein.
The COA page shows how these lines appear on a certificate and what a lot result adds to them.
When the other grade is the wrong one
WPC 80 is the wrong choice when the product has to be clear, when the lactose figure has a hard ceiling, or when the fat the concentrate carries would push the panel past what the label promises. WPI 90 is the wrong choice when the powder is going into a bar that benefits from the fat and lactose for texture and flavour, when foam is part of the product, or when the process has no way to justify separating the protein further than the formula needs.
Neither grade is settled by the protein figure on the front of the pack. It is settled by the dose, the matrix and the label, and then written into the specification. The product page carries the catalogue limits for WPC 80, and the compliance page covers how the grade is declared in the EU, the US and the UK.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation