06 Identity & adulteration

How to prove a lot is sodium caseinate

Technical document 06 · Reviewed 2026-11-20 · Sodium Caseinate

On this page
  1. The four identity layers
  2. The sodium ratio: proving the salt
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

Four measurements, read together, identify a sodium caseinate lot: the document names the salt and the CAS number, the protein pattern shows casein, the sodium figure shows the sodium salt, and the ash and moisture close the mass balance. No single line does it. A protein figure of 90% is consistent with sodium caseinate, calcium caseinate and micellar casein, so the cation is the deciding measurement.

In one line

A sodium caseinate lot is the sodium salt when the protein pattern, the sodium figure and the ash agree: the protein says casein, the sodium says which caseinate, and the ash shows the mineral load.

The four identity layers

A certificate can carry the right name and still leave the powder unproven. The four layers below ask separate questions and each needs its own evidence. A supplier who answers only the first has described the paperwork, not the drum.

Four layers of sodium caseinate identity
LayerQuestionTestWhat it proves
DocumentIs the salt named?Name, CAS number, specificationPaperwork and traceability
ProteinIs the protein casein?SDS-PAGE and amino acid profileThe protein family
Counter-ionIs it the sodium salt?Sodium and calcium by ICP-OESThe cation
Mass balanceIs it diluted or boosted?Protein, ash, moisture, lactoseConsistency of the numbers

The fourth layer is the one that catches a blend. A powder made from sodium caseinate and a nitrogen-rich filler can be formulated to land inside the protein range, but the ash, the sodium or the amino acid profile moves. The numbers have to be read together.

The sodium ratio: proving the salt

The catalogue range is 1.0–1.5% sodium, which is 0.43–0.65 mmol of sodium per gram of powder. Calcium caseinate at 1.0–1.5% calcium carries 0.25–0.37 mmol of calcium per gram, or 0.50–0.75 meq, because calcium is divalent. The two salts neutralise a similar charge with a different mass of cation, which is why the sodium and calcium figures separate them while the protein figure does not.

Sodium by ICP-OES is the direct test. A result inside 1.0–1.5%, with protein at 90.0% dry basis and ash at 4.0% or below, is consistent with the sodium salt. A sodium result near zero with a normal ash points to calcium caseinate or micellar casein; a sodium result above 1.5% with ash above 4.0% points to added sodium salt or a different neutralisation. A high sodium with low protein points to a diluent.

The protein-to-sodium ratio is a useful screen, not a specification: at 90% protein and 1.2% sodium the ratio is about 75 to one, and it falls as sodium rises. It catches a blend that has been balanced on protein alone. The ICP-OES method note explains the digestion and the reporting limits.

X-ray diffraction and the solid state

X-ray diffraction is the wrong tool for proving the salt form of caseinate, and it is worth saying so. Casein is amorphous: a diffractogram shows a broad halo and no crystalline peaks, so XRD cannot separate sodium caseinate from calcium caseinate or from micellar casein. A laboratory that offers an XRD identity test for caseinate is selling a pattern that will look the same for all three.

XRD is still useful for a different question: whether a crystalline solid has been added. Lactose, melamine, a mineral salt or a crystalline diluent can produce peaks in an otherwise amorphous powder. That makes XRD a screen for adulteration rather than a release test for identity. FTIR is more informative about the protein but still not form-specific: the amide bands show that the material is protein, not which cation is bound.

The practical analytical set is the mineral panel plus the protein pattern plus the mass balance. The XRD method note sets out what a pattern can and cannot support.

What adulteration looks like

Substitution routes for sodium caseinate and their signals
RouteWhat movesSignalTest
Calcium caseinateSodium down; calcium upSodium below 1.0%; calcium presentICP-OES, ash
Micellar caseinSodium down; ash lower; thicker dispersionSodium low; dispersion swellsMineral panel, dispersion test
Whey proteinAmino acid pattern; lactose may riseProtein passes; pattern differsSDS-PAGE, amino acid profile, lactose
Plant proteinForeign protein bandsAmino acid pattern differsSDS-PAGE, amino acid profile
Nitrogen boosterProtein high; amino acids lowKjeldahl and amino acid disagreeAmino acid profile, melamine screen
Sodium chloride or diluentSodium and ash up; protein downAsh above 4.0%; sodium above 1.5%ICP-OES, ash, protein mass balance

The last route is the one that a sodium figure alone can miss. Sodium chloride lifts the sodium result without adding casein, and the ash rises with it. The protein figure and the amino acid profile are the check. A milk-protein ELISA confirms that the material is milk-derived, but it does not separate the caseinates, because all of them are milk protein.

How to write identity into the specification

  • “Sodium caseinate, CAS 9005-46-3, made by neutralising acid casein with sodium hydroxide.”
  • “Protein ≥90.0% on a dry basis, Kjeldahl with N × 6.38; report the factor and the moisture.”
  • “Sodium 1.0–1.5% by ICP-OES; ash ≤4.0%; calcium reported beside the sodium.”
  • “Protein pattern by SDS-PAGE conforms to the casein reference; amino acid profile on request.”
  • “Moisture ≤6.0%; fat ≤1.5%; particle size ≥95% through 80 mesh.”
  • “Milk declared; lot number, site and retained sample identified on the COA.”

The specification makes identity testable only if the methods are named. A line that says “identity conforms” without the protein pattern, the mineral method and the reference has left the form untested.

Five questions for the supplier

  1. Which salt is this lot, and which CAS number is on the certificate?
  2. What are the sodium, calcium and ash figures, and by which method were they measured?
  3. Can you supply the SDS-PAGE pattern and the amino acid profile, not only the protein percentage?
  4. What is the moisture, and how was the dry-basis protein calculated?
  5. On a disputed lot, would you accept a joint re-test against the retained sample?

Those five answers make an identity file; one protein percentage does not. The catalogue specification is on the sodium caseinate product page; the release tests are on the COA page; the powder forms are compared on the grades page; the other salt is on the calcium caseinate page; the methods section explains the techniques; and the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation