Sodium caseinate grades: powder form, protein and sodium
Sodium caseinate is sold as one ingredient name but in more than one powder form. The protein window is similar across the range — at least 90.0% on a dry basis — and the choice is usually the physical form, the flow and the way the powder wets and disperses. The grade decision is therefore made on the mixer and the pack, not only on the certificate.
The grade is the powder form plus the protein-and-sodium window, not the protein figure alone; form, flow and dispersion decide how the same 90% caseinate behaves in a mixer.
Why sodium caseinate comes in grades
Sodium caseinate is made by neutralising acid casein with sodium hydroxide and spray-drying the solution. The chemistry is the same across the range; what changes is the drying and the finishing. A standard spray-dried powder is milled to 80 mesh. An instantized or agglomerated version is built from larger, porous particles that wet faster and throw less dust. Both are sodium caseinate, and both read the same protein on a dry basis.
The grade matters because the powder is often the limiting step in a filling line. A fine 80 mesh powder disperses well once it is in the mixer, but it can dust, bridge in a hopper and float on the surface of water. An agglomerated powder wets more evenly and fills a sachet at a different bulk density. Neither is a better material in the abstract; each suits a different plant.
The two powder forms side by side
| Point | Standard 80 mesh | Instantized / agglomerated |
|---|---|---|
| Particle size | ≥95% through 80 mesh | Larger agglomerates; sieve profile agreed |
| Bulk density | Higher | Lower; more air between particles |
| Dust | More fines | Less dust |
| Wetting | Slower; can float | Faster; sinks and wets |
| Dispersion | Good with shear | Good with less shear |
| Filling | Less volume per gram | More volume per gram |
| Typical use | General powder and bar use | Stick packs and hand-mixed drinks |
The table gives directions, not a specification. Agglomeration changes the particle size, the bulk density and the wettability; it does not change the protein, the sodium or the allergen. If the filling line is already set for an 80 mesh powder, an instantized grade can need a new fill weight and a new line trial.
What changes in the drum and in the mixer
Sodium caseinate is freely soluble in water and gives a slightly turbid solution. That solubility is the reason it is chosen over micellar casein in a drink: it hydrates without the swelling and thickening that a micellar powder brings. The solution is still not clear, and a formulation that needs a transparent drink has to test the powder in the real matrix rather than assume clarity from the word “soluble”.
Viscosity is the practical limit. A higher solids load thickens the mix, and the effect depends on the protein concentration, the temperature and the shear. A powder that disperses easily at 5% can still be difficult at 15%, and the grade does not change that curve. Trial the load that will be sold, at the process temperature, before the specification is fixed.
The 80 mesh figure is a sieve pass, not a mean particle size. Two lots can both pass 80 mesh and behave differently because one carries more fines. When flow or dust is the problem, ask for the sieve profile and the bulk density, not only the pass statement. The particle-size glossary entry explains the convention.
How much the formula can carry
A 90.0% dry-basis figure at the 6.0% moisture ceiling works out to about 84.6% protein as weighed. A 20 g serving supplies about 16.9 g of protein and, at 1.0–1.5% sodium, between 200 and 300 mg of sodium. A 30 g serving supplies about 25.4 g of protein and 300–450 mg of sodium. Those figures are arithmetic, not a recommendation, and they belong on the label before the dosage form is fixed.
A powder stick is the simplest format: the consumer adds water, so the ingredient sees no heat process and no long hold in solution. A ready-to-drink product is harder. The caseinate has to survive homogenisation and the heat step, and the viscosity has to stay inside the filling window. A bar is a third case: water activity rather than solubility decides the texture, and the protein can firm over shelf life.
A capsule or tablet takes the powder at 80 mesh with a fill weight sized on the protein and the sodium. Tableting can be difficult at high caseinate loads because the powder is cohesive; a granulated or instantized grade may flow better, but it changes the fill weight. Trial the dosage form before the specification is agreed.
What to write into the specification
The form belongs in the first line, and the protein basis belongs beside the protein figure. A specification that says only “sodium caseinate” leaves the powder form, the mesh and the sodium window open.
- Product: sodium caseinate, CAS 9005-46-3, made by neutralising acid casein with sodium hydroxide.
- Protein: ≥90.0% on a dry basis, Kjeldahl with N × 6.38, factor and basis printed.
- Mineral: sodium 1.0–1.5% by ICP-OES; ash ≤4.0%.
- Composition: fat ≤1.5%; moisture ≤6.0%.
- Physical: ≥95% through 80 mesh, or the agreed agglomerated profile; bulk density stated.
- Allergen: milk declared on the specification and the COA.
- Contaminants and microbiology: the limits on the COA page.
When a different casein is the better choice
Calcium caseinate is the alternative when the formula can take calcium instead of sodium, or when a colloidal dispersion and a different heat behaviour suit the process. It is a different salt, not a drop-in: the mineral line, the solubility and the label name all change. The comparison is set out on the sodium versus calcium caseinate page.
Micellar casein is the choice when the formula wants body and a lower mineral load, and when the plant has the shear and the time to hydrate it. Whey protein is a different protein with a different amino acid pattern and a different label. None of these should be selected on the protein percentage alone; the form, the cation and the process all move together.
One grade across a product line is usually worth more than a separate optimisation for each SKU. A second powder form means a second specification, a second fill trial and a second line on the label.
The catalogue specification is on the sodium caseinate product page; the release tests are on the COA page; the market rules for the label are on the compliance page; the other salt is on the calcium caseinate page; the methods section explains the protein and mineral tests; and the quality page describes release.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation