01 COA & batch testing

What the COA for sodium caseinate actually contains

Technical document 01 · Reviewed 2026-11-20 · Sodium Caseinate

On this page
  1. What the sheet has to list
  2. Dry basis, the nitrogen factor and the sodium line
  3. Catalogue limit, release limit and lot result
  4. What moves between lots
  5. When an outside laboratory earns its fee
  6. What to compare between suppliers

A sodium caseinate certificate reports protein by Kjeldahl on a dry basis with N × 6.38, the sodium figure that identifies the salt, and the remaining composition, physical and microbiological lines. The protein says how much casein is present, the sodium and ash say which caseinate it is, and the moisture converts the dry-basis figure to the powder as weighed. Release limits belong to the specification; results belong to the lot, in separate columns.

In one line

A sodium caseinate certificate is read on a dry protein basis with the sodium and ash beside it: the protein says how much casein, the sodium says which salt, and the moisture converts both to the powder as weighed.

What the sheet has to list

The parameter list follows the specification rather than a template. Composition and physical lines describe the powder and its handling; contaminants and microbiology describe what came with it. A sodium caseinate sheet is not complete without the protein basis and the sodium figure, because those two lines separate this salt from calcium caseinate and from micellar casein.

Composition and physical parameters · sodium caseinate, catalogue limits
ParameterMethodRelease limit
AppearanceVisualOff-white to cream powder
Protein (dry basis)Kjeldahl, N × 6.38≥90.0%
SodiumICP-OES1.0–1.5%
AshGravimetric, furnace≤4.0%
FatSolvent extraction≤1.5%
MoistureLoss on drying≤6.0%
IdentificationProtein patternConforms to the reference
Particle sizeSieve≥95% through 80 mesh

The sodium line is often left off a generic protein certificate, yet it is what shows the powder is the sodium salt rather than the calcium salt or a micellar grade.

Contaminants and microbiology · sodium caseinate, catalogue limits
ParameterMethodRelease limit
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
Total plate countPlate count≤1,000 cfu/g
Yeast and mouldPlate count≤100 cfu/g
E. coliEnrichmentAbsent
SalmonellaEnrichmentAbsent

The method column is not decoration: a sodium result without ICP-OES beside it cannot be compared with one from another technique, and a plate count depends on the medium, the temperature and the time. A result without its method is a summary.

Dry basis, the nitrogen factor and the sodium line

Kjeldahl measures nitrogen and multiplies it by a factor. Milk protein uses 6.38, a factor that assumes nitrogen is about 15.7% of protein mass; the general factor of 6.25 assumes 16%. The gap looks small and is not: a 90.0% result calculated with 6.38 becomes about 88.2% if the same nitrogen is multiplied by 6.25. The factor belongs beside the figure, not in a method footnote.

The basis moves the number further. This specification is on a dry basis, so the 6.0% moisture ceiling is excluded from the protein calculation. At that ceiling, 90.0% dry basis corresponds to 84.6% as-is (90.0 × 0.94), and a 20 g serving of the powder supplies about 16.9 g of protein. Dropping the basis puts a purchase order out by more than five points before analytical variation.

Sodium is a separate line, not a conversion of the protein. The catalogue range is 1.0–1.5%, measured by ICP-OES, and it is the figure that proves the salt. At 1.2% sodium, a 20 g serving carries about 240 mg of sodium; at the top of the range it carries 300 mg.

Catalogue limit, release limit and lot result

Three statements are easy to mix up. The catalogue limit is the window this grade is sold inside; the release limit is the narrower one agreed for a customer or a market; the lot result is the measurement. The first two are promises, and only the third is evidence.

What the result column should contain
ParameterCatalogue limitResult column
Protein≥90.0% dry basisA measured percentage with the factor, basis and moisture
Sodium1.0–1.5%A measured percentage by ICP-OES
Ash≤4.0%A measured percentage, read beside the sodium figure
Moisture≤6.0%A measured percentage
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 80 meshThe measured percentage through the sieve

“Conforms” is a conclusion, not a measurement. The reader should be able to reach it from the numbers and their methods. A certificate that repeats the specification in the result column has told the buyer nothing about the lot.

What moves between lots

Sodium caseinate starts with acid casein, and the casein starts with skim milk. Feed, stage of lactation and season move the protein and the mineral content of the milk, and the neutralisation and washing steps can only narrow that variation. A lot that drifts to the top of the sodium range usually does so because more alkali was bound, not because sodium was added as salt.

Drying decides the moisture, the colour and the way the powder wets. A hot inlet produces a free-flowing powder that wets slowly; a gentler dry leaves more moisture and disperses more easily. The mill and the sieve then set the particle-size result, so the 80 mesh figure can move while the protein chemistry stays put.

Trends matter more than a single result near an edge. Protein drifting low while ash climbs can point to a different casein wash; sodium climbing while protein stays steady can point to a neutralisation change. The lot code on the certificate should be the one printed on the pouch, the drum and the retained-sample label.

When an outside laboratory earns its fee

Independent testing is worth it for a new source, a first shipment into a regulated market, a form the certificate does not prove, or a disputed result. The panel should answer the open question rather than repeat the sheet: protein by Kjeldahl at a second laboratory, sodium, calcium and phosphorus by ICP-OES, an amino acid profile, SDS-PAGE for the protein pattern, lactose by HPLC, a melamine and cyanuric acid screen, and the microbiological set on the same sample.

A milk-protein ELISA confirms that the material is milk-derived; it does not separate sodium caseinate from calcium caseinate or from micellar casein, because all three are milk protein. The salt question is answered by the mineral panel. The methods section explains what each technique proves, and the quality page describes how the sample and the lot record are kept.

What to compare between suppliers

Compare six lines: protein with its factor and basis; sodium and ash with methods; fat and moisture; particle size plus a dispersion result; the allergen statement; and the site and lot traceability. Offers that match at 90% protein but differ on sodium, ash or moisture are not the same powder.

The record is the second test. Ask which site ran the lot, which casein batch went in, which neutralisation and drying steps were used, and which retained sample is held. A certificate can be accurate and still describe a lot other than the one that arrives.

The catalogue specification is on the sodium caseinate product page; the tests that separate the salt forms are on the identity page; the market rules are on the compliance page; and the calcium caseinate page gives the other side of the salt comparison.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation