How we prove a phycocyanin lot is the pigment
A phycocyanin lot is the named material when the spectrophotometric identity, the pigment figure, the protein figure and the mass balance agree. The visible blue is a clue, not a test: a synthetic dye can match the hue, and a blue-green whole-spirulina powder can look close in colour. Identity is proved by the spectrum and by what else the powder contains.
Identity is a spectrum plus a mass balance: the absorbance maximum near 620 nm says phycocyanin, the protein and ash say what else is in the powder, and colour alone says nothing.
The four identity layers
Naming the material on paper is the easy part; proving that the powder is that material takes separate measurements. The layers below ask different questions, and each one needs its own evidence. An answer that stops at the first layer describes a document, not a drum.
| Layer | Question | Test | What it proves |
|---|---|---|---|
| Document | Is the material named? | Name, CAS number, source | Paperwork only |
| Spectrum | Is the pigment phycocyanin? | UV/Vis scan, 500–700 nm | The chromophore and its protein environment |
| Protein | Is the powder a protein concentrate? | Kjeldahl nitrogen × 6.25 | Protein mass, including the pigment |
| Mass balance | Is it diluted or dyed? | Moisture, ash, dye screen | Consistency of the numbers |
The 620/280 ratio and what it does not say
Phycobiliprotein work often quotes a purity index: the absorbance at 620 nm divided by the absorbance at 280 nm. The 620 nm reading sits on the pigment; the 280 nm reading sits on the aromatic amino acids of the protein. A high ratio means the preparation is rich in phycocyanin relative to other proteins, and a low ratio means the powder carries more non-pigmented protein or dilution. The index is useful for comparing preparations, but the thresholds depend on the method, the buffer and the standard, so a number without those details is not a grade.
The catalog specification does not set a 620/280 ratio, and we do not use one as a release gate. It is a supporting check, not an identity test: a dyed powder can be made to absorb at 620 nm, and a pure phycocyanin can lose ratio after heat damage. Read it beside the protein figure, the ash and the spectrum rather than on its own.
The turbidity correction is the other ratio that matters. The 620 nm reading is corrected with a reading at 650 nm, where the pigment absorbs little, so that suspended particles do not inflate the result. A certificate that reports the pigment percentage without the wavelength pair has left the correction invisible.
X-ray diffraction: the wrong primary tool here
Phycocyanin is an amorphous protein preparation, not a crystalline small molecule. X-ray diffraction is therefore a poor identity test for it: there is no sharp pattern to match, and a “conforms” statement without a reference does not prove the pigment. A supplier who offers XRD as the identity evidence for this material has offered a method that does not answer the question.
XRD still has a narrow use. It can detect a crystalline adulterant, such as a mineral filler or a crystalline dye, in a powder that should be amorphous. If a lot is suspected of carrying such a filler, ask for the pattern, the reference and the detection limit, and read the result as a screen for that contaminant rather than as proof of phycocyanin. For the identity itself, the spectrum and the protein figure carry the argument.
What adulteration looks like
| Substitute | Effect on the powder | Signal | Test to run |
|---|---|---|---|
| Whole spirulina | Green powder; lower pigment per gram | Green hue; chlorophyll; low 620/280 ratio | Microscopy, spectrum, pigment figure |
| Synthetic blue dye | Matches the colour, not the protein | Blue without a protein spectrum; dye peak | UV/Vis scan, HPLC dye screen |
| Other phycobiliproteins | Similar chemistry, different spectrum | Shifted maximum; extra peak | Full spectrum, chromatography |
| Maltodextrin or salt | Dilutes pigment and protein | Low pigment and protein; high ash or moisture | Mass balance, ash |
| Chlorophyll | Green cast; masks the blue | Green hue; absorption near 660 nm | Spectrum, visual |
Colour is the weakest signal. A dye can reproduce the blue, and a green cast can be read as a natural variation. The stronger signals are the shape of the spectrum, the protein figure and the mass balance. A certificate that reports appearance and a pigment percentage but no spectrum has not tested the substitution most likely to occur.
What the identity clause should say
- “Phycocyanin, CAS 11016-15-2, from Arthrospira platensis.”
- “Identification by UV/Vis spectrum from 500 to 700 nm; maximum near 620 nm; report the wavelength pair and the standard.”
- “Phycocyanin ≥25.0% by UV/Vis with turbidity correction; state the basis.”
- “Protein ≥50.0% by Kjeldahl, nitrogen × 6.25.”
- “Moisture ≤7.0%; ash ≤8.0%; ≥95% through 80 mesh.”
- “No synthetic colourant and no added carrier above the stated limit.”
- “Destination and label name confirmed before the order.”
Five questions for the supplier
- Can you provide the full UV/Vis spectrum, not only the pigment percentage?
- Which wavelength pair and standard were used for the pigment figure, and on which basis is it reported?
- What is the protein result, and which nitrogen factor was applied?
- What are the moisture and ash results, and do they close the mass balance with the pigment and protein?
- Has the lot been screened for synthetic blue colourants, and what was the detection limit?
Those five answers, taken together, are the identity file. One assay percentage is not. The product page holds the catalogue values; the COA page maps each number to its certificate line; the grades page compares the formats; the level-four page separates the isolate from the whole alga; the methods library explains the spectrophotometric reading.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation