Phycocyanin grades: colour value, pigment assay and format
Phycocyanin is sold on two different specifications: a colour value used by the food-colour trade and a percentage of phycocyanin by UV/Vis used by supplement buyers. The catalog grade is a spray-dried blue powder at ≥25.0% phycocyanin and ≥50.0% protein; the format and the assay tier are separate decisions from the colour it produces. The grade you buy should be the one the label, the dosage form and the destination can live with.
The grade is a specification language before it is a number: colour value for a colourant buyer, pigment percentage for a supplement buyer, and the two do not convert without the method.
Why phycocyanin grades are hard to line up
A food-colour buyer describes the material by the colour it gives a solution. That figure is an absorbance of a defined dilution at 620 nm, often expressed as a colour value, and it depends on the dilution, the path length and the reference. A supplement buyer describes the same powder as a percentage of phycocyanin by UV/Vis and a percentage of protein by Kjeldahl. Both descriptions can be true of one lot, and neither one can be calculated from the other without the method and the standard.
The practical result is that two quotations can both say “phycocyanin” and mean different products. One may be a colourant grade selected on hue intensity, the other a supplement grade selected on pigment and protein per gram. The first question to ask is which number the buyer will use to release the lot.
Powder, granulated powder and liquid concentrate
The catalog form is a milled powder at 80 mesh. Granulation and a liquid concentrate are different formats with different handling, not different purities. The table sets out what changes when the format changes.
| Property | Catalog powder | Granulated powder | Liquid concentrate |
|---|---|---|---|
| Phycocyanin (UV/Vis) | ≥25.0% | Same assay, granulated | Quoted per lot |
| Protein (Kjeldahl) | ≥50.0% | Same assay, granulated | Lower per gram, because the liquid contains water |
| Moisture | ≤7.0% | ≤7.0% | Water is the carrier |
| Appearance | Blue, free-flowing powder | Blue granules | Deep blue liquid |
| Handling | Dusts; needs a seal | Lower dust; better flow | Needs a chilled, dark store |
| Pack | 1 kg foil pouch, 25 kg drum | On request | On request |
| Usual use | Capsules, tablets, powder blends | Blends that need flow | Drinks made on site |
The liquid concentrate is the format to avoid unless the process can handle it. It carries water, needs a cold chain or a preservative decision, and its shelf life is shorter than the powder's. It is convenient for a beverage plant that dissolves the pigment the same day; it is a poor choice for a capsule line.
Colour, solubility and pH
The powder dissolves in water to a deep blue solution. The colour is pH-dependent: it is most stable in the mildly acidic to neutral range, and below about pH 4 the blue weakens and shifts toward green as the protein unfolds. That is a formulation constraint, not a defect in the lot. An acidic drink, a fruit-flavoured stick or a tablet with an acidic excipient should be checked for colour after storage, not only at mixing.
Heat and light both attack the chromophore. A process that pasteurises the solution in clear glass combines two of the failure modes at once, and the colour can fade within the hold. The powder is hygroscopic; a pouch left open in a humid room takes up moisture and cakes, and the caked material is harder to weigh and slower to dissolve.
Dose arithmetic with a 25% powder
The pigment figure is the bridge between the label and the weigh-up. A formula that targets 100 mg of phycocyanin per serving needs 100 ÷ 0.25 = 400 mg of a 25.0% powder. That same 400 mg carries about 200 mg of protein at the 50.0% minimum. The arithmetic is not a dose recommendation; it is the calculation that keeps the label and the batch record consistent.
For a colour application, the target is usually a shade in the finished product rather than a milligram figure, and the use level is found by trial in the matrix. The overage question belongs to the formulator: a colour that fades over shelf life can be dosed higher at the start, but the label, the use level and the destination rules have to support the number. Do not set an overage by assumption and then write it into the specification as if it were an assay.
What to write into the specification
- “Phycocyanin, CAS 11016-15-2, from Arthrospira platensis; blue, free-flowing powder.”
- “Phycocyanin ≥25.0% by UV/Vis at 620 nm with turbidity correction; state the basis.”
- “Protein ≥50.0% by Kjeldahl, nitrogen × 6.25; state that the pigment is part of this figure.”
- “Moisture ≤7.0%; ash ≤8.0%; ≥95% through 80 mesh.”
- “Heavy metals and microbiology as listed; report each element separately.”
- “Format: powder, granulated or liquid, with the pack and the storage condition.”
- “Destination, use level and label name confirmed before the order.”
We supply the powder. Granulation is a separate specification, and the liquid concentrate is a different purchase with its own pack and shelf life. A change of format should go through a written change control rather than a line on the order.
When a different grade is the wrong buy
If the buyer's release number is a colour value, a certificate built only on the pigment percentage has not answered the question; ask for the colour value method and the reference. If the release number is the pigment percentage, a colour-grade certificate without the UV/Vis method and basis is not comparable. The two languages describe one powder, but they are not interchangeable on a specification.
Whole spirulina is not a grade of phycocyanin. It is the dried alga, green rather than blue, with a much lower pigment fraction and a different label name; the comparison is on the level-four page. The product page carries the catalogue values; the COA page shows how each figure is reported; the stability page covers the colour loss; the methods library describes the spectrophotometric reading; the quality page covers the release file.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation