03 Stability

Phycocyanin stability: the blue fades first

Technical document 03 · Reviewed 2026-11-19 · Phycocyanin

On this page
  1. The powder: moisture, light and colour
  2. The solution: the least stable format
  3. What drives degradation
  4. A stability protocol for the ingredient
  5. The finished formula changes the answer
  6. How the shelf life is set

The blue chromophore is the first thing to go. Phycocyanin bleaches under light, denatures under heat and shifts away from blue as the pH falls, while the dry powder pulls moisture from the air. A sealed, dark, dry pack is the only format that keeps the colour through a normal shelf life, and the retest period has to be earned for that pack.

In one line

The blue is the vulnerable part: light and heat bleach the chromophore, moisture and pH move the protein, and the pack decides how much of that the powder sees.

The powder: moisture, light and colour

Moisture is the quiet failure. The 7.0% limit is a release measurement, not a property the drum keeps. Spray-dried phycocyanin is hygroscopic: open the pouch in a humid room and the powder starts to take up water, the loss on drying climbs, the as-is pigment figure falls and the powder begins to cake. The seal, the liner and the storage humidity matter as much as the release gate, although the certificate does not print them.

Light acts faster. The chromophore exists to absorb visible light, which is exactly why the powder is blue and exactly why it is fragile. A clear jar on a bench is an exposure, and the surface can lose shade within days. Keep the material in the foil pouch or in an opaque container that actually closes.

Warmth multiplies both effects. A sealed pack usually survives an ambient warehouse; it does not survive a hot loading bay, a car boot or a greenhouse. After cold storage, let the pack reach room temperature before opening, so condensation does not settle on the powder.

The solution: the least stable format

Dissolved in water, the protein is fully exposed. Light, oxygen, heat and pH act at once, and the blue can fade while the protein figure still looks acceptable. A ready-to-drink line adds a pasteurisation or hot-fill step; a powder stick avoids that heat because the consumer adds water at the point of use.

pH is the variable that catches formulators out. The blue is stable in the mildly acidic to neutral range, and below about pH 4 it weakens and turns toward green as the protein unfolds. A fruit drink built at pH 3.2 can lose the shade that looked right in water at pH 6. If the matrix is acidic, validate the colour in the matrix rather than in a buffer.

A liquid can be protected with an opaque pack, a pH inside the stable band, low dissolved oxygen and a validated hold time, but each of those is a process decision that has to be tested. A bulk-powder result does not transfer to a beverage: the matrix, the heat load and the pack each change the rate.

What drives degradation

Factors that move phycocyanin during storage
FactorEffect on the powder or solutionControl
LightBleaches the chromophore; pigment assay fallsOpaque or foil pack; dark store
HeatUnfolds the protein; accelerates colour lossCool process; controlled store
MoistureRaises loss on drying; cakes; lowers the as-is assaySealed pouch; desiccant where needed
pHShifts the blue toward green; precipitation near the isoelectric pointValidate matrix pH; buffer if needed
OxygenSurface and dissolved oxidationLow headspace; nitrogen flush where specified; sealed pack
Metal ionsProtein binding and colour change in solutionAvoid iron and copper contact

These factors combine rather than add. A warm, bright, humid store is worse than three separate stresses, and an acidic drink in clear glass stacks four of them in one container. The useful question is not whether phycocyanin is stable, but for how long it stays blue in a named pack and matrix.

A stability protocol for the ingredient

Build the study around the failure modes, not only around the standard conditions. A long-term arm (25 °C, 60% relative humidity) and an intermediate arm (30 °C, 65% relative humidity) model the warehouse; an accelerated arm (40 °C, 75% relative humidity) stresses the pack. For this material, add a light-exposure arm, because a dark incubator cannot see the main failure.

At each pull, measure pigment by UV/Vis, protein by Kjeldahl, moisture, ash, appearance and microbiology. Record colour as a number rather than as “blue”, so a drift is visible before it becomes a reject. Ask for the individual results, not a summary that says stable, and ask which pack and lot family the study used.

Buy the study that matches the pack you will buy. A 25 kg drum and a 1 kg pouch differ in headspace and in opening history, and a result from a different format is a starting point rather than a substitute.

The finished formula changes the answer

A capsule or tablet keeps water activity low, but the shell and the excipients can still pass moisture, and an acidic excipient can move the local pH. Check moisture and colour at release and after storage, not only the fill weight. A two-piece shell that is clear exposes the fill to light even when the outer carton is opaque.

A stick pack depends on the foil and the seal; a pinhole fails the pack, so inspect the strip as well as the powder. A beverage combines light, pH, heat and oxygen, so the bulk stability result is only a starting point.

The formulator decides whether a colour overage is needed. That decision belongs to the label and stability file, and it cannot repair a pack that lets light or moisture in. An overage written into the batch record but not declared on the label creates a different problem from a colour that fades.

How the shelf life is set

There is no single shelf-life figure for phycocyanin, because the pack and the storage condition set it. The retest period on the specification is supported by the stability file for that pack; a number quoted without a pack, a condition and a test panel is a claim rather than a shelf life.

At the end of the retest period, re-assay the retained sample before extending use. Never add time without a new assay, and never apply a bulk figure to a container that has been repacked. The product page shows the packs on offer; the COA page lists what is released; the grades page compares formats; the methods library explains the pigment assay; the quality page shows the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation