How we prove a pea protein lot is the isolate
A lot is pea protein isolate when four measurements agree: the protein figure against its nitrogen factor and dry basis, the amino acid profile behind that protein, the ash and fat that the isolate is allowed to carry, and the physical form of the powder. Each of those can be satisfied by a different powder. Four tests, then, rather than one — because the protein percentage on its own is the weakest evidence in the file.
A pea isolate is proved by four measurements together — protein against its factor, the amino acid profile, the ash and fat floor, and the amorphous powder — because any single one can be satisfied by a different powder.
Four tests, four questions
Layer one is the nitrogen result: Kjeldahl, N × 6.25, dry basis, read against the 80.0% floor. It measures nitrogen, not identity.
Amino acids come next. Pea runs high in lysine and arginine and limited in methionine and cysteine, which is the shape of a legume protein rather than a cereal or a dairy one. Add a foreign protein and the pattern moves; add nitrogen that is not protein and it does not move at all.
Layer three is what the protein is not: moisture ≤8.0%, ash ≤5.0%, fat ≤2.0%. Ash and fat are the two that separate an isolate from a concentrate and from a blend; moisture is the simplest check in the set.
Layer four is the powder itself: an amorphous spray-dried solid at 80 mesh, with a pH in the stated window and a defined dispersion behaviour, rather than a blend, a crystallised lot or a different process.
The factor, and the ratios that follow
At 6.25, nitrogen is taken as 16% of protein; an 80.0% figure therefore sits on about 12.8% nitrogen. Two ratios do most of the work. The first is protein to ash: at 80.0% protein and 5.0% ash the ratio is 16:1, while a concentrate at 55% protein and 6% ash sits near 9:1. An 80% protein figure beside a concentrate-level ash result points to a blend, or to nitrogen that is not all protein.
Protein to fat is the second ratio: at 80.0% protein and 2.0% fat the floor is 40:1. A fat figure three times the ceiling is not the isolate this specification describes, whatever the certificate says at the top.
The amino acid sum gives a third check. Acid hydrolysis loses part of the tryptophan and cysteine, so the sum expressed as protein usually lands a little under the Kjeldahl figure. A gap of two or three points is normal analytical loss; five or more suggests some of the nitrogen is not protein nitrogen. As an illustration, 1% melamine in the powder would read as about 4.2 points of protein under 6.25, 1% urea as about 2.9, and 1% glycine as about 1.2. None of those shows up as protein in the amino acid profile, and every one of them lifts the headline figure.
What XRD and FTIR can settle
A spray-dried isolate is amorphous, so its X-ray diffraction pattern should be a broad halo with no sharp reflections, which is itself evidence of the drying route. A sharp reflection points to a crystalline phase — pea starch from a concentrate or flour, a crystalline sugar or sugar alcohol used as a carrier, a crystalline amino acid such as glycine or leucine, or an inorganic salt. It is also the fastest check for a drum that has crystallised in storage.
FTIR adds the functional-group view: the amide I band near 1650 cm⁻¹ and amide II near 1545 cm⁻¹ belong to the protein backbone, while the carbohydrate region shows starch or sugar. Against a reference spectrum of the same grade, FTIR confirms the material class quickly; it does not quantify protein. Each method note — XRD, FTIR — sets out what the technique can and cannot settle.
Where substitution shows up
| Route | What it changes | Test that catches it |
|---|---|---|
| Concentrate blended in | Fibre and starch up, protein down, colour deeper | Protein, carbohydrate by difference, XRD for starch |
| Other protein added | Amino acid pattern shifts, foreign DNA present | Amino acid profile, PCR or ELISA |
| Starch or maltodextrin | Carbohydrate up, protein down, crystalline starch on XRD | Carbohydrate, XRD, iodine |
| Non-protein nitrogen | Kjeldahl up, amino acid sum unchanged | Amino acid profile, LC-MS/MS |
| Amino acid spike | Profile abnormal, crystalline phase possible | Amino acid profile, XRD |
| Excess water | Moisture above limit, caking | Moisture, water activity |
The first three routes are commercial substitutions: a lower grade sold as a higher one, or a blend that meets the protein figure while missing the ash and fat ceilings. Non-protein nitrogen is the safety-critical route, and it is why a protein figure without an amino acid profile is an incomplete identity file.
What the specification has to fix
- The grade, the process and the physical form: pea protein isolate, alkaline extraction and isoelectric precipitation, spray-dried, 80 mesh.
- Protein, with the factor and basis stated: ≥80.0% by Kjeldahl on a dry basis, N × 6.25.
- Moisture, ash and fat, each as a limit with its method.
- An amino acid profile, reported in g per 100 g of protein rather than as one figure.
- A non-protein nitrogen screen, melamine by LC-MS/MS where the risk exists, run at release rather than once a year.
- The allergen statement: pea, and any shared legume or cereal line.
A specification that stops at protein, moisture and ash describes a white powder, not a pea isolate. These lines and their methods are laid out on the COA page.
Five questions to ask
- What nitrogen factor and basis are on the certificate, and can the nitrogen result be shown alongside the protein figure?
- Can you supply the lot's amino acid profile, and does its sum match the Kjeldahl result?
- What ash and fat limits apply to the grade you are quoting, and are they run on every lot or only written into the specification?
- Which method was used to screen for melamine or another non-protein nitrogen, if any?
- Does the retained sample carry the same lot number as the drum?
Every one of these is a fair question; a supplier who cannot answer them is showing a powder, not documenting it. How far isolate and concentrate can sit apart is on the grade comparison, and the catalogue limits a specification starts from are on the product page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation