What the COA for milk protein concentrate actually contains
The certificate for a milk protein concentrate lot lists the protein figure by Kjeldahl with its factor and its basis, the moisture that converts it to the powder as weighed, then fat, lactose, ash, the contaminant panel, microbiology and particle size. Each line carries the method and the release limit, and the grade belongs on the certificate too: the 70 and the 85 grades do not share a protein floor.
The protein figure is a nitrogen measurement: the grade, the N × 6.38 factor and the dry basis decide the number, and fat, lactose and ash describe what else is in the drum.
The parameter list
Milk protein concentrate has no CAS number, because it is not a single substance. It is the protein of skim milk — casein and whey — dried with the lactose, fat and minerals the separation left behind. The certificate is a composition sheet, and protein is only the first line.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | Off-white to light tan powder |
| Protein, dry basis | Kjeldahl, N × 6.38 | ≥80.0% |
| Moisture | Loss on drying | ≤6.0% |
| Fat | Solvent extraction | ≤2.0% |
| Lactose | HPLC | ≤5.0% |
| Ash | Gravimetric, furnace | ≤7.0% |
| Particle size | Sieve analysis | ≥95% through 80 mesh |
| Parameter | Method | Release limit |
|---|---|---|
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and enrichment | APC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent |
The grade sits above the sheet. The catalogue line here is the 80 grade: protein ≥80.0% dry basis, fat ≤2.0%, lactose ≤5.0%, ash ≤7.0%. A 70 grade has a lower protein floor and more lactose and ash; an 85 grade has less. The grade comparison sets out what moves, and a certificate without the grade number cannot be matched to the purchase order.
Dry basis, as-is and the nitrogen factor
Kjeldahl digests the sample, traps the nitrogen released and multiplies by 6.38, the dairy convention that assumes nitrogen is about 15.7% of milk protein. The protein percentage is a calculation from that nitrogen, and the calculation has two variables that must be printed.
The first is the basis. An 80.0% dry-basis result on a lot with 6.0% moisture is 75.2% of the powder as weighed; the same 80.0% at 4.0% moisture is 76.8%. Both lots can be released against the same catalogue line and they deliver different amounts of protein per kilogram, so the moisture belongs beside the protein.
The second is the factor. 6.38 is the dairy convention and 6.25 the general food convention; the same nitrogen read through 6.25 returns a figure about 2% lower. A certificate without the factor cannot be compared with one built on a different factor, and the gap is wider than the batch spread a buyer is trying to control.
Fat, lactose and ash are reported as-is; a page that carries a dry-basis protein beside an unlabelled fat has invited the reader to subtract one from the other.
Release limit versus batch result
A release limit is the acceptance boundary for the lot; a batch result is what the laboratory measured. Both belong on the page, in separate columns, with the method named. A result column that repeats the limit is not a result.
| Parameter | Release limit | Result column |
|---|---|---|
| Protein | ≥80.0% dry basis, N × 6.38 | A measured percentage, with the nitrogen result and the factor |
| Moisture | ≤6.0% | A measured percentage, from which the as-is protein is calculated |
| Fat and lactose | ≤2.0% and ≤5.0% | A measured percentage for each, as-is |
| Ash | ≤7.0% | A measured percentage, as-is |
| Heavy metals | Per element | A figure in mg/kg for each element |
| Microbiology | Counts and absence | The count and the absence statement for the lot |
“Passes specification” is a conclusion the reader should be able to reach from the numbers. For a dairy protein the result that matters most is not always a metal: melamine or urea raises the Kjeldahl result without raising the protein, so a certificate that reports only the percentage has shown that the powder contains nitrogen. The identity page covers the amino-acid check that closes that gap.
What moves between batches
Milk is a seasonal raw material. Fat and lactose follow the lactation curve and the feed, ash follows the mineral balance, and a winter lot and a summer lot from one plant can differ enough in lactose and fat to change a bar or a drink. The supplier’s own range allows for this, which is why a comparison should use results rather than the range.
The process adds variation: ultrafiltration and diafiltration decide how much lactose and ash are removed, the heat step decides how much whey protein is denatured, and the dryer and the sieve set the particle result. None of that changes the grade name, and each can change how the powder behaves in the customer’s mixer.
Read the trend across lots rather than one result: ash climbing, lactose climbing or moisture creeping says more than a lot at the edge of the range, and a markedly darker lot can point to a harder heat step or to browning while protein, fat and lactose all pass.
When to order an outside test
Order an independent test for a new source, a first shipment, a grade claim the certificate does not prove, or a disputed result. The useful panel is protein by Kjeldahl with the factor stated, moisture, fat, lactose, ash, the metal panel, microbiology and a total amino-acid profile. The amino-acid sum is the direct check on the protein figure: a nitrogen-rich adulterant lifts the nitrogen without lifting the amino acids.
Add a casein-to-whey separation when the material is claimed to be milk protein concentrate rather than a whey or casein product; caseins precipitate at pH 4.6 while the whey proteins stay in solution, so the fractions can be weighed separately. Add melamine and cyanuric acid screens for a dairy lot from a source with no history.
Ask the laboratory to report its detection limit for every screen; a “not detected” line without a limit is evidence about the method, not the sample. Keep the tested pack as the retained sample and put the lot code on the report.
What to compare between suppliers
Put seven points side by side: grade and protein with the basis and the factor; moisture; fat, lactose and ash as separate results; the heat treatment; particle size and whether the grade is instantized; the metal and microbiology results; the pack and the lot code. Two quotations that agree on “80% protein” and differ on lactose, ash or heat treatment are not the same ingredient.
The second layer is traceability: the plant, the milk source, the heat step and the dryer. The specification is on the milk protein concentrate product page. The grade options are on the grades page, the ratio against whey protein on the level-four comparison, and the lactose method in the HPLC method note. The release workflow is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation