06 Identity & adulteration

How we prove an egg white protein lot is egg white

Technical document 06 · Reviewed 2026-11-20 · Egg White Protein

On this page
  1. Four layers of evidence
  2. The nitrogen factor and the amino acid ratios
  3. X-ray diffraction and the solid state
  4. How substitutions show up
  5. What the specification should say about identity
  6. Five questions worth asking

An egg white protein lot is identified by four agreeing measurements: the source and ingredient name, protein by Kjeldahl with N × 6.25, an amino acid profile that matches egg white, and a mass balance of moisture, fat and ash. The egg allergen statement is part of the identity file, because the material is egg-derived by definition.

In one line

A lot is egg white protein when the nitrogen, the amino acid pattern and the mass balance all agree, and none of them leaves room for a carrier.

Four layers of evidence

A certificate can carry the right name and still leave the material unproved. Each layer below settles a separate question, and a supplier who stops at the first has described a document rather than a powder.

Four layers of egg white protein identity
LevelWhat it asksTechniqueWhat it establishes
DocumentIs the source and form named?Name, source, specificationPaperwork only
ProteinHow much nitrogen is present?Kjeldahl, N × 6.25Total nitrogen, not which protein
ProfileIs the protein egg white?Amino acid profile or electrophoresisThe protein pattern
Mass balanceIs the powder diluted?Moisture, fat, ash, carbohydrateConsistency of the numbers

The order matters. The document check is cheap and necessary; the protein check is the headline; the profile is the layer that separates egg white from whey, soy or collagen; and the mass balance catches a powder that is mostly protein plus a carrier. A lot can pass the first two and fail the last two.

The nitrogen factor and the amino acid ratios

Egg white protein is calculated as nitrogen × 6.25. That factor is the arithmetic that turns the Kjeldahl result into a protein figure, and it is fixed by the specification rather than by the certificate layout. At 80.0% protein on a dry basis with 8.0% moisture, the powder is 73.6% protein as weighed; the other 26.4% is water, fat, ash and carbohydrate, not a second protein.

The amino acid profile is the fingerprint. Egg white protein has an arginine-to-lysine ratio near 0.8, while whey sits near 0.25 and soy is higher still; its sulfur amino acids, methionine and cysteine together, run at about 6 g per 100 g of protein against about 4 g for whey. Hydroxyproline should be absent, because its presence points to collagen or gelatin. These are typical published ratios, not release limits, and the lot profile is what the specification should require.

The ratio is a fingerprint, not a purity assay. A blend can be built to land near the egg white pattern on the main amino acids, and the mass balance is what catches the rest. Read the profile with the protein, moisture and ash together, and ask for the full table rather than a summary of “protein profile conform”.

X-ray diffraction and the solid state

Spray-dried egg white protein is amorphous. Its X-ray diffraction pattern is a broad halo with no sharp crystalline peaks, and that is the expected result for the pure powder. Sharp peaks mean a crystalline component: lactose, maltodextrin, a salt or another carrier added as a diluent. For a product sold as pure egg white protein, that is a finding worth explaining.

XRD is not a protein assay and cannot tell egg white from whey. It answers the solid-state question, and its value is in catching a crystalline diluent that the protein figure alone would not reveal. Pair it with Fourier-transform infrared spectroscopy, where the amide I band around 1650 cm⁻¹ and the amide II band around 1545 cm⁻¹ confirm the protein backbone and the carbohydrate region shows a sugar carrier.

Before accepting a “conforms” note, ask to see the reference pattern and the detection limit. A diffractogram with nothing to compare it against is a picture, not an analysis. The XRD method page and the FTIR method page set out what each technique can and cannot settle.

How substitutions show up

Common egg white protein substitutions and the signals
SubstituteEffect on the powderWarning signTest
Whey or milk proteinCheaper protein with a similar figureAmino acid pattern shifts; arginine lowProfile, milk ELISA
Soy proteinCheaper protein; changes the profileArginine high; soy markersProfile, soy ELISA
Collagen or gelatinRaises the nitrogen figure cheaplyHydroxyproline presentHydroxyproline by HPLC
MaltodextrinDilutes the powderProtein low; crystalline peaksMass balance, XRD
Urea or melamineInflates Kjeldahl nitrogenProtein high against the profileLC-MS/MS nitrogen screen

The non-protein nitrogen route is the one that catches buyers most often, because it defeats the protein test without adding any protein. The amino acid profile is the first check: if the nitrogen says 85% and the summed amino acids say 70%, the gap is the question. The second check is a direct screen for urea and melamine.

Colour and taste are weak signals. Off-white to light tan covers a wide range, and a fine powder looks like another fine powder. The stronger evidence is the profile, the mass balance and the nitrogen screen.

What the specification should say about identity

  • “Egg white protein (dried egg white), source: hen egg white.”
  • “Protein ≥80.0% on a dry basis by Kjeldahl, N × 6.25.”
  • “Moisture ≤8.0%; fat ≤1.0%; ash ≤5.0%.”
  • “Identification by amino acid profile against an egg white reference.”
  • “Allergen statement: contains egg.”
  • “No added protein, carrier or non-protein nitrogen source.”
  • “Particle size ≥95% through 80 mesh.”

The allergen line is not decoration. A specification that names egg white protein but leaves the allergen statement to the invoice has left the most consequential label fact to a document that is not controlled with the specification.

Five questions worth asking

  1. Which egg source and which drying process produced this lot?
  2. What is the nitrogen result, and which factor was applied?
  3. Can you provide the full amino acid profile, not only the protein percentage?
  4. Is any carrier, added protein or nitrogen source present, and how is it declared?
  5. In a dispute, would you test the retained sample jointly with us?

Those answers, taken together, are an identity file; a protein percentage on its own is not. The product page carries the catalogue specification, the COA page explains how each result is reported, the grades page compares the powder forms, and the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation