03 Stability

Egg white protein stability: moisture, heat and the pack

Technical document 03 · Reviewed 2026-11-20 · Egg White Protein

On this page
  1. The powder: moisture is the first limit
  2. The solution: heat, pH and microbial load
  3. What moves the powder
  4. Designing the stability trial
  5. How the finished format changes it
  6. Where the retest period comes from

Spray-dried egg white protein keeps well when it stays dry and cool. Moisture uptake causes caking and browning, heat denatures the protein and lowers its solubility, and a warm, humid store shortens the usable period. The pack and the storage condition set the retest period; the certificate does not.

In one line

Dry and cool are the two conditions the powder needs; moisture and heat are what turn a soluble egg white protein into a caked, browned powder.

The powder: moisture is the first limit

The catalogue sets moisture at ≤8.0%. That is a release limit, not a storage allowance. Egg white protein is hygroscopic, and an opened pouch equilibrates with the room: the moisture figure climbs, the powder picks up water at the particle surface, and the particles stick together. Once the lumps form, they do not break up on shaking, and the powder no longer disperses cleanly.

Water also drives chemistry. Egg white contains a small amount of glucose, and glucose reacts with the lysine in the protein during warm or moist storage. The result is a darker powder, a changed flavour and less available lysine. The reaction is slow in a sealed pack at ambient temperature and much faster in a warm, humid filling room or a pouch left open on a bench.

A desiccant is useful in a humid climate but cannot replace a proper closure. The foil pouch is the barrier; a clear jar is not, however convenient it looks. If the pack is cold when it arrives, let it reach room temperature before opening, so that no condensation forms on the powder.

The solution: heat, pH and microbial load

Egg white protein disperses in water to a clear to slightly opalescent liquid. That liquid is also a good medium for microorganisms, and it is sensitive to heat: egg white proteins begin to denature around 60 °C and are substantially changed by 80 °C, so a process hot enough to pasteurise a drink is hot enough to change its protein. A ready-to-drink product therefore needs a validated heat process, a pH hurdle or another preservation step, and the validation has to be done in the drink.

pH matters as well. Near the isoelectric point of the egg white proteins, around pH 4.5–5.5, solubility is at its lowest and a drink can turn hazy or sediment. A neutral or mildly acidic shake is easier to hold than an acidic one, and the formulator should check the appearance at the intended pH before fixing the process.

Foam is a physical behaviour rather than a stability failure. Egg white foams when shaken or pumped, and a filling line that needs a still surface will see it. A powder stick avoids the problem until the consumer adds water; a ready-to-drink line has to manage it with the process and the equipment.

What moves the powder

What moves the powder in storage
VariableEffectControl
MoistureCaking, browning, loss of dispersibilitySealed foil pouch; dry store; desiccant where needed
HeatDenatures protein; lowers solubility; accelerates browningCool store; controlled process temperature
OxygenOxidises the small fat fraction; off-flavourLow headspace; sealed pack
LightColour fade or shift at the surfaceOpaque or foil pack; dark store
pH, in solutionHaze and sediment near the isoelectric pointValidate the matrix pH; buffer if needed
MicroorganismsGrowth in a reconstituted liquidValidated heat process or another hurdle

These factors act together. A warm, humid store combines moisture and heat, and a clear bottle of reconstituted drink on a sunny bench combines light, heat and microbial growth. The useful question is not whether egg white protein is stable, but under which pack, at which condition and for how long.

Designing the stability trial

Write the protocol around four decisions: which pack, which storage condition, which time points and which tests. For the warehouse, run a long-term arm at 25 °C/60% relative humidity and an intermediate arm at 30 °C/65%; for the pack, add an accelerated arm at 40 °C/75%. A light-exposure arm covers the surface colour change that a dark incubator misses.

Test protein by Kjeldahl with the 6.25 factor, moisture, appearance, dispersibility and the microbiological count at each point. For an instantized grade add bulk density and wetting time, because the agglomerate can lose its advantage before the protein figure moves. For a stick pack, test the seal as well as the powder: a pinhole is enough to let moisture in.

Request the stability summary that was generated for the pack in your purchase order. A 25 kg fiber drum and a 1 kg foil pouch differ in headspace, surface-to-volume ratio and how often they are opened, and the data belongs to the pack rather than to the product family.

How the finished format changes it

A protein bar is the hardest common format. The bar has a water activity that allows moisture to move between phases, and the sugars and the protein are in contact for months. Egg white protein can contribute to hardening as the proteins rearrange and the water redistributes, and the bar has to be tested as a bar, not as a powder.

A capsule or tablet starts dry, but the fill is hygroscopic and the shell or the excipients can move moisture into it. Compression adds heat and pressure, and a tablet that was stable as a powder can pick up moisture from the air after packing. A stick pack fails at the seal; a ready-to-drink fails at the heat step or at the pH. None of these formats simply takes the bulk pouch's shelf life with it.

Where the retest period comes from

There is no single shelf-life figure for egg white protein: it depends on the pack and on how the pack is stored. The retest period on the specification is the number that counts, and it should point to the stability file for that pack. A figure that names neither the pack nor the storage condition nor the test panel is not a shelf life.

At the end of the retest period, assay the retained sample again before extending use. Never extend on assumption, and never apply a drum figure to a pouch that was repacked from it. The product page sets out the standard packs; the COA page describes the release tests; the MOQ page gives the pack sizes and lead time; the microbiology method note describes the counts; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation