01 COA & batch testing

What the COA for corn zein actually contains

Technical document 01 · Reviewed 2026-11-20 · Corn Zein

On this page
  1. The certificate as a test report
  2. Dry basis, the nitrogen factor and the mass balance
  3. Release limit versus batch result
  4. What moves between lots
  5. When to order an outside test
  6. What to compare between suppliers

A corn zein certificate reports the protein figure with its nitrogen factor and basis, the fat and ash ceilings that separate food-grade zein from corn gluten meal, the moisture, the protein-profile identification and the contaminant and microbiology panels. Each line needs a method, a release limit and a measured result. The limits below are the catalog specification; the batch COA is the document that confirms a particular pack.

In one line

The protein figure on a zein certificate is a nitrogen calculation on a stated basis, and the fat, ash and moisture beside it decide whether the powder is the grade that was ordered.

The certificate as a test report

A certificate is useful when a reviewer can reconstruct the release decision from the page: what was measured, which method produced the number, and which limit the lot was released against. Zein is defined by a protein fraction and by what is not there — fat, ash, fibre and moisture — so a single protein percentage leaves the other axes open.

Release parameters for corn zein
ParameterMethodRelease limit
AppearanceVisualOff-white to cream powder
IdentificationProtein profileConforms to the reference
ProteinKjeldahl nitrogen, N × 6.25, dry basis≥90.0%
FatSolvent extraction≤2.0%
AshGravimetric≤1.0%
MoistureLoss on drying≤8.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

Dry basis, the nitrogen factor and the mass balance

The catalog protein limit is ≥90.0% on the dry basis, calculated from Kjeldahl nitrogen multiplied by 6.25. The factor is a convention: it assumes 16% nitrogen in the protein, and it belongs on the certificate. A result without the factor cannot be reproduced.

The basis is the second convention. A result on the dry basis is the protein divided by the dry matter. A powder at 92.0% dry-basis protein and 6.0% moisture carries 92.0 × 0.94 = 86.5% protein as received. The same powder can be reported as 92.0% or 86.5% depending on the column heading. Neither is wrong; mixing them is.

The mass balance is the third check. Convert the protein to the as-is basis before adding fat, ash and moisture: 86.5% protein + 2.0% fat + 1.0% ash + 6.0% moisture = 95.5%, leaving about 4.5% for carbohydrate and other matter. If the as-is figures add up to more than 100%, one of the lines has been reported on the wrong basis. That is the most common arithmetic error on a zein certificate.

The FCC monograph for zein sets protein at 88.0–96.0% on the dry basis, fat at ≤2.0% and loss on drying at ≤8.0%. The catalog is tighter on protein (≥90.0%) and adds ash ≤1.0%. A lot can meet the monograph and miss the catalog, so the specification revision belongs beside the certificate.

Release limit versus batch result

Two columns are often conflated: the limit the lot must meet, and the value the laboratory found. The first is the specification; the second is the evidence. A result column that repeats the limit has told the reader nothing about the lot.

The limit and the measured value are different columns
ParameterRelease limitResult column
Protein≥90.0% dry basis (N × 6.25)A measured percentage, with the factor and the basis
Fat≤2.0%A measured percentage and the extraction method
Ash≤1.0%A measured percentage
Moisture≤8.0%A measured percentage
Heavy metalsPer elementA figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot

“Passes specification” is a conclusion the reader should be able to reach from the numbers. For microbiology the evidence is a count plus an absence statement; for heavy metals it is a figure per element, not a total that hides the element that matters.

“Protein profile conforms” is only useful when the certificate names the reference pattern or the gel image; otherwise the line is an opinion. Ask for the profile when the source is new.

What moves between lots

Four process steps move the numbers. The corn source sets the protein and the colour. The extraction with alkaline aqueous isopropyl alcohol sets the fat and the ash: a longer or hotter extraction can raise the protein and shift the colour, while a carry-over of sodium hydroxide raises the ash. Precipitation and drying set the moisture and the solvent residue. Milling sets the mesh and the dust.

Fat is the line that separates zein from corn gluten meal. A zein grade at ≤2.0% fat is a different material from a gluten meal at several times that figure. The protein figures can look similar while the fat, fibre and colour are not. That is why the fat ceiling belongs in the first table, not in a footnote.

Colour is a weak signal: a shade inside the off-white to cream range is not a failure, and the batch record is more useful than a photograph.

Across lots, look at direction: protein drifting down, fat or ash climbing, moisture rising with the season, or a solvent result approaching the agreed limit. The lot code should match the pouch, the drum and the retained sample.

When to order an outside test

Order an independent test for a new source, a regulated market, a film claim the certificate does not support, or a disputed lot. Target the decision rather than repeat the whole certificate.

The core panel is Kjeldahl protein with the factor and basis, fat, ash, moisture, protein profile by SDS-PAGE or the agreed method, amino acid analysis, ICP-MS for the heavy metals, and microbiology. Two zein-specific checks are worth adding: solubility in aqueous ethanol, where the powder is insoluble in water and soluble in the alcohol, and a mycotoxin panel, because corn can carry aflatoxin and fumonisin. If the specification carries a residual-solvent limit, test for the solvent named in the process; the route described in 21 CFR 184.1984 uses isopropanol.

A “not detected” line without a detection limit is evidence about the method, not about the sample. Ask for the limit with the result. Keep the tested sample and the lot record; a referee test needs both.

What to compare between suppliers

Put six lines side by side: CAS number and source fraction; protein result with the factor and basis; fat, ash and moisture; protein profile and solubility; contaminants and microbiology; pack and lot code. Two certificates that agree on protein but differ on fat or basis are not describing the same powder.

The second layer is traceability: who manufactured the lot, which corn fraction and solvent were used, and which drying and milling steps were applied. The catalog values sit on the corn zein product page. The identity page covers the tests that separate zein from corn gluten meal and peptides; the grades page covers mesh and granulation; the methods library explains the panels; the quality page describes release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation