06 Identity & adulteration

How we prove a corn zein lot is zein

Technical document 06 · Reviewed 2026-11-20 · Corn Zein

On this page
  1. The identity layers
  2. The nitrogen factor, the dry basis and the mass balance
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Five questions for the supplier

A corn zein lot is the named material when four measurements agree with the document: the protein figure is on the dry basis with N × 6.25, the protein profile shows the zein pattern, the powder is insoluble in water but soluble in aqueous alcohol, and the amino acid pattern is corn-like. The document must name the prolamine and CAS 9010-66-6, and the protein figure alone cannot separate zein from corn gluten meal or a corn peptide.

In one line

Identity is the agreement of four measurements: the nitrogen figure on its basis, the protein profile, the aqueous-alcohol solubility and the amino acid pattern.

The identity layers

A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Layers of corn zein identity
LayerQuestionTestWhat it proves
DocumentIs the material named?Name, CAS 9010-66-6, sourcePaperwork only
NitrogenIs the protein figure real?Kjeldahl with the factor and basisTotal nitrogen, not the fraction
ProfileIs the protein zein?SDS-PAGE or the agreed profileThe prolamine pattern
SolubilityIs it the prolamine?Water and aqueous alcoholThe characteristic solubility
Amino acidsIs the source corn?Amino acid analysisA source fingerprint
Mass balanceIs it diluted?Protein, fat, ash and moisture togetherConsistency of the numbers

The nitrogen factor, the dry basis and the mass balance

Protein is calculated from nitrogen: the Kjeldahl result multiplied by an agreed factor, 6.25 in the usual case. That factor is a ratio, and it belongs on the certificate. A result of 15.0% nitrogen becomes 93.75% protein at 6.25, but a different factor would give a different number from the same powder. The factor is a convention, not a measurement.

The basis is the second ratio. Protein on the dry basis is the as-is protein divided by the dry matter. A powder at 92.0% dry-basis protein and 6.0% moisture carries 92.0 × 0.94 = 86.5% protein as received. The same powder can be reported as 92.0% or 86.5% depending on the column heading; mixing the two is the common error.

The mass balance is the third check. Add the as-is protein to the fat, ash and moisture: 86.5% protein + 2.0% fat + 1.0% ash + 6.0% moisture = 95.5%, leaving about 4.5% for carbohydrate and other matter. A certificate that adds 92.0 + 2.0 + 1.0 + 6.0 = 101.0 has put the protein on the dry basis and the other lines on the as-is basis. The total is the tell.

The amino acid pattern is the source ratio. Zein is high in glutamic acid, proline, leucine and alanine and low in lysine and tryptophan. Corn gluten meal shares the corn source but carries more fat and fibre; soy protein is much higher in lysine; wheat gluten has its own pattern and a gluten ELISA signal. Tryptophan needs its own hydrolysis method because acid hydrolysis destroys it, so a certificate that reports tryptophan from a standard acid hydrolysis has reported a number it cannot defend.

X-ray diffraction: the solid-state check

Zein is an amorphous protein, and its X-ray diffraction pattern is a broad halo rather than a set of sharp peaks. XRD is therefore not a routine release test for zein, and a “conforms” statement against an amorphous reference adds little on its own. It becomes useful when the question is whether the powder contains a crystalline carrier or a salt: a sharp pattern is a signal to ask what else is in the blend.

If a supplier offers XRD as identity evidence, ask for the pattern, the reference and the detection limit. It does not measure the protein fraction, and it does not prove the corn source. It is a supporting solid-state check, not a substitute for the nitrogen, profile, solubility and amino acid data.

What adulteration looks like

Common corn zein substitutions and the signals
AdulterantWhat it doesSignalTest
Corn gluten mealRaises yield; adds fat and fibreFat high; colour darker; protein lowerFat, fibre, protein profile
Corn protein peptidesAdds water-soluble proteinDissolves in water; peptide presentSolubility, peptide HPLC
Wheat glutenAdds a similar prolamineGluten detected; profile differsGluten ELISA, SDS-PAGE
Soy proteinRaises protein and lysineLysine high for corn; soy detectedAmino acid profile, soy ELISA
Starch or maltodextrinDilutes the powderProtein low; iodine or sugar signalMass balance, iodine test
MoistureLowers the as-is proteinMoisture high; dry-basis figure normalLoss on drying

The simplest substitutions are the ones that move the protein figure, because the protein figure is the number most buyers check first. The fat, the solubility and the amino acid pattern are the checks that make the substitution visible. Colour is the weakest signal: off-white to cream covers a wide range of powders, including blends.

How to write the identity into the specification

  • “Corn zein, CAS 9010-66-6, source Zea mays; state the corn fraction and the extraction route.”
  • “Protein ≥90.0% by Kjeldahl, N × 6.25, dry basis; state the factor and the basis.”
  • “Fat ≤2.0%; ash ≤1.0%; moisture ≤8.0%; appearance off-white to cream.”
  • “Identification by protein profile; state the reference pattern or method.”
  • “Solubility: insoluble in water, soluble in aqueous alcohol; name the test solvent.”
  • “Amino acid profile on file, with lysine and tryptophan reported by a validated method.”
  • “No corn gluten meal, corn peptide or other protein above the agreed limit; allergen and GMO statements for the lot.”

A specification built this way gives the laboratory something to test and the buyer something to compare. A single line that says “corn zein 90%” gives neither. The product hub carries the catalog values; the COA page shows where each figure sits on the certificate; the grades page covers mesh and granulation; the zein versus corn peptide comparison covers the material choice; the methods library explains the analytical options; the quality page describes the release file.

Five questions for the supplier

  1. Which corn fraction and extraction route produced this lot, and is the CAS number on the certificate?
  2. What are the protein factor and basis, and what are the fat, ash and moisture results?
  3. Can you provide the protein profile and the amino acid analysis, not only the protein percentage?
  4. What is the solubility in water and in the named aqueous alcohol?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single protein percentage does not.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation