What the COA for collagen tripeptide actually contains
A collagen tripeptide certificate has to answer three questions that sound alike: how much protein the powder contains, how much of it is peptide, and how much is three residues long. The first is a nitrogen calculation, the second a size separation, the third a chromatographic measurement against a defined standard. A certificate that reports only the first has not described this product.
Protein, peptide and tripeptide are three different measurements of the same powder; a certificate is auditable only when each carries its method, its limit and a loss-on-drying result.
What the certificate has to show
A batch certificate is a test report. Every row should let a reader reconstruct the release decision without asking the supplier what a number meant. That requires three columns as a minimum: the parameter, the technique that produced the value, and the limit the lot was released against. A results column is what turns the report into evidence.
| Test | Technique | Limit for release |
|---|---|---|
| Appearance | Visual | Off-white to pale yellow powder |
| Protein | Kjeldahl, N × 5.55 | ≥90.0% |
| Tripeptide content | HPLC | ≥30.0% |
| Peptide content | SEC-HPLC | ≥80.0% |
| Loss on drying | Gravimetric | ≤7.0% |
| Ash | Gravimetric, furnace | ≤5.0% |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Particle size | Sieve analysis | ≥95% through 80 mesh |
Protein, peptide and tripeptide are the rows that matter. Protein says how much nitrogenous material is present. Peptide content says how much of the powder behaves as peptide rather than as free amino acid or salt. Tripeptide content says how much of it is the short fraction. A lot can satisfy the first and miss the third.
Three denominators: protein, peptide and tripeptide
Protein is the broadest figure. The laboratory digests the sample, measures nitrogen and multiplies by 5.55, the factor used for collagen because its nitrogen sits near 18% of the protein mass. The result is usually reported on a dry basis, which is why the moisture line matters: 90.0% protein at 7.0% loss on drying equals about 83.7% of the powder as weighed. A buyer comparing an as-is figure with a dry-basis figure is comparing two different powders.
Peptide content comes from a size separation. SEC-HPLC sorts the soluble material by molecular size and reports the share that falls in the peptide window, excluding free amino acids and salts. The result is a share of the material, not a share of the protein figure, and the certificate should say which detector and which calibration were used.
Tripeptide content is the narrowest figure. The HPLC method separates the low-mass fraction and integrates the peaks that correspond to three-residue peptides, but “tripeptide” is a class, not a single peak. The certificate should name the standard, list which peptides are counted and state the integration rules. Without that, 30.0% is a number that another laboratory may not reproduce.
One ratio is useful. If a lot sits at the floor on both counts, 30.0% tripeptide inside 80.0% peptide means tripeptides make up 37.5% of the peptide fraction. A lot that reports 34% and 82% is not the same material, even though both pass.
The gate and the result are different columns
A release limit is the boundary the lot had to stay inside. A result is what the instrument read on that lot. Printing the limit twice, once as a “result”, is the most common way a certificate looks complete while saying nothing. The table below sets out what the result column should contain for each release test.
| Test | Limit | Result entry |
|---|---|---|
| Protein | ≥90.0%, dry basis, N × 5.55 | A percentage with the factor and basis stated |
| Tripeptide content | ≥30.0% by HPLC | A percentage and the chromatogram |
| Peptide content | ≥80.0% by SEC-HPLC | A percentage and the size distribution |
| Loss on drying | ≤7.0% | A measured percentage |
| Heavy metals | Per element | A separate mg/kg figure for each element |
| Microbiology | Counts and absence | The lot count and the absence statement |
A line that reads “complies” is a conclusion, not a measurement. The reader cannot audit it, compare it with another lot or use it in a finished-product calculation. For this product the tripeptide row deserves the closest reading, because it is the one that cannot be inferred from any other result.
Where lots drift
The raw material sets the starting composition, and the hydrolysis decides how far the chains are cut. A longer hydrolysis pushes the curve toward smaller peptides; the fractionation step then decides how much of that small fraction is kept. Change the membrane cut-off or the concentration factor and the tripeptide figure can move by several points while the protein result stays flat.
Drying changes the loss on drying and the colour. Milling and sieving change only the particle-size result, which is why an 80 mesh figure can move when the mill is serviced without any chemistry changing. Colour is the least quantitative signal: off-white to pale yellow is a wide window, and a shift inside it is not a grade failure. A powder that becomes distinctly darker or duller has usually met moisture and heat together, and the retained sample is the right comparison.
Single results near a limit are less informative than a trend. Results clustered just above the floor tell a different story from results spread around 34%, even though both sets pass. Plot the tripeptide and peptide figures against the lot date and read the direction.
Independent testing: when and what
An outside laboratory is worth its time when the source is new, when the destination is regulated and the file is being built, when a tripeptide statement is central to the label, or when a result is disputed. The panel should be chosen to answer the open question rather than to repeat the whole certificate.
For a source qualification, ask for protein with the factor, hydroxyproline as the collagen marker, tripeptide content with the chromatogram, SEC-HPLC distribution, species PCR and the contaminant panel on the same sample. Ask every laboratory for its detection limit; “not detected” without a limit says nothing about the sample. Keep the sample identity and the lot code with the report.
Reading two quotations side by side
Line up six items: the protein result with its factor and basis; the tripeptide result with its definition; the peptide content and distribution; the loss on drying and ash; the species and tissue; the pack, metals and micro results. Two offers that agree on protein but differ on tripeptide are offers for different materials.
Then check traceability. The certificate should identify the manufacturer, the tissue, and the hydrolysis, fractionation, drying and milling steps. The catalogue specification is on the collagen tripeptide product page. The analyses that separate this fraction from a standard collagen peptide are described on the identity page; the chromatographic method is in the HPLC method note; the wider methods section covers the other techniques; the release workflow is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation