Tripeptide content, peptide content and source: choosing a collagen tripeptide grade
Collagen tripeptide is sold as one catalogue grade, but three variables still have to be fixed on the specification: the tripeptide floor, the peptide content and the source. Within the grade, the powder is supplied at 80 mesh and can be granulated on request, and that choice changes flow, dust and fill weight. The grade decision is therefore a specification decision, not a choice between brand names.
The grade is the tripeptide figure, the peptide distribution and the source; the protein percentage alone does not describe any of the three.
Why the tripeptide figure is the grade
Collagen is hydrolysed to make peptides, and the hydrolysate is then fractionated to enrich the smallest chains. A tripeptide is three amino acids long. The most common one in collagen is glycine-proline-hydroxyproline, with a molecular weight of about 285 Da, and it is one of the reasons the tripeptide fraction is separated from the rest of the hydrolysate. The catalogue floor is ≥30.0% tripeptide by HPLC; the rest of the powder is a mixture of dipeptides, longer peptides, free amino acids and salts.
The floor is a share, not a purity. A product at 30.0% tripeptide is not 70% impurity: most of the remaining mass is collagen peptide that has not been cut to three residues. That is why the tripeptide figure has to be read beside the peptide content, which is specified at ≥80.0% by SEC-HPLC. The two figures together say how much of the powder is peptide and how much of that peptide is the short fraction.
Protein is the third figure and the least specific. At ≥90.0% by Kjeldahl with N × 5.55, it confirms that the powder is protein-rich, but it cannot distinguish a tripeptide-enriched fraction from a standard collagen peptide. A supplier who quotes only protein has not quoted this product.
The two collagen products side by side
| Figure | Collagen tripeptide | Standard collagen peptides | What it decides |
|---|---|---|---|
| Protein (N × 5.55) | ≥90.0% | ≥90.0% | Nitrogen mass, not peptide size |
| Tripeptide content | ≥30.0% by HPLC | — | The fraction this product is bought for |
| Peptide content | ≥80.0% by SEC-HPLC | ≥90% below 3,000 Da by SEC-HPLC | Share of mass in the peptide range |
| Hydroxyproline | — | 8.0–12.0% | Collagen marker |
| Loss on drying | ≤7.0% | ≤7.0% | Storage behaviour and as-is basis |
| Ash | ≤5.0% | ≤2.0% | Mineral residue |
| Particle size | ≥95% through 80 mesh | — | Flow, dust and dispersion |
The two columns are different specifications, not two positions on one scale. The standard peptide is defined by a molecular-weight cut-off with no tripeptide floor; this product is defined by a tripeptide floor. The comparison is taken further on collagen tripeptide versus collagen peptides.
The powder in the drum
The catalogue appearance is an off-white to pale yellow, free-flowing powder. The colour is a little warmer than the white to off-white of a standard collagen peptide, and a shift within that window is not a grade change. The material is hygroscopic, so the powder should be handled in a dry room and the pack closed between weighings; an open scoop left on a bench will pick up moisture and begin to cake.
At 80 mesh the powder is finer than a 40 mesh material, which improves dispersion in a stick pack but increases dust and static during weighing. Granulation is available on request. It changes the particle size and the flow, not the tripeptide or peptide figures, and the granulation aids have to be named in the specification and on the certificate.
The ash limit of ≤5.0% is wider than the ≤2.0% typical of a standard collagen peptide. Ash is the mineral residue left after ignition, and a lot that sits near the limit deserves a question about the fractionation and neutralisation steps rather than an automatic rejection. The number is a gate; the batch record explains it.
What the grade means in the finished product
For capsules and tablets, the constraint is mass per serving and flow on the press. A 500 mg fill holds 500 mg of powder, so the tripeptide delivered depends on the batch figure: 500 mg at the 30.0% floor is 150 mg of tripeptide, and a lot at 35.0% delivers 175 mg in the same fill. That is arithmetic for the label and the weigh-up, not a suggested intake.
For powder sticks and drink mixes, the constraint is dispersion and taste. The finer powder wets out quickly and gives a clear to slightly opalescent solution at typical use levels; a granulated grade disperses more cleanly in a shaker but may take longer to wet. Neither change alters the chemistry, and neither is a reason to accept a different tripeptide figure.
State the tripeptide figure on the specification, not only the protein range. A formula built on a 30.0% material and switched to a 35.0% lot delivers more tripeptide for the same fill weight, which is a label and change-control question rather than a manufacturing convenience. The COA page shows where the figure is reported.
What to write into the specification
- “Collagen tripeptide, hydrolysed collagen fraction; source species and tissue stated on the certificate.”
- “Protein ≥90.0% by Kjeldahl (N × 5.55), with the factor and basis printed on the COA.”
- “Tripeptide content ≥30.0% by HPLC; method, standard and integration rules stated.”
- “Peptide content ≥80.0% by SEC-HPLC; distribution reported, not only the total.”
- “Loss on drying ≤7.0%; ash ≤5.0%; particle size: at least 95% through 80 mesh.”
- “Heavy metals Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg; microbiology as listed; allergen statement naming the source.”
A specification that names only protein and appearance does not describe this grade. The three figures, the source and the particle size are what a laboratory can test against and what a purchaser can compare between suppliers.
When the standard grade is the better buy
If the formula already carries several grams of collagen peptides per serving and the tripeptide figure is not part of the purchase, the standard peptide grade is the simpler specification. It has a hydroxyproline range, a molecular-weight cut-off and a wider document base, and it does not require the tripeptide method to be agreed and validated.
If the label names “collagen peptides” rather than a tripeptide fraction, switching the material to this grade changes the declared ingredient and the grams per serving. That is not a like-for-like substitution, and it should be handled as a formulation change with a new label review. The catalogue specification for the standard grade sits on the collagen peptides product page, and the full catalogue for this product is on the collagen tripeptide product page. The supporting analyses are set out on the identity page, and the methods section explains the assays behind the figures.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation