02 Grade comparison

Calcium caseinate, sodium caseinate or micellar casein: choosing the form

Technical document 02 · Reviewed 2026-11-20 · Calcium Caseinate

On this page
  1. Why the process is the grade
  2. The three casein forms side by side
  3. The powder, the mixer and the dispersion
  4. How much protein and calcium the formula carries
  5. Specification lines for the grade
  6. When another casein form is the better choice

Calcium caseinate is one of three casein materials sold for supplements and foods. The two caseinates, calcium and sodium, read 90% protein on a dry basis; micellar casein reads 80%. The protein line alone cannot identify the material, so the grade decision turns on the cation, the process and the label name.

In one line

The grade is the form of the casein: calcium caseinate, sodium caseinate and micellar casein differ in the cation, the process and the label, so the powder cannot be substituted on protein percentage alone.

Why the process is the grade

Casein is a family name. CAS 9000-71-9 identifies casein rather than a physical form, and the caseinate salts are listed separately: calcium caseinate is 9005-43-0 and sodium caseinate 9005-46-3. The process creates the form, so the grade is a route and the properties that come with it.

Both caseinates start with acid casein. Skim milk is acidified to about pH 4.6, where the casein precipitates; the curd is washed, which removes lactose and much of the colloidal calcium phosphate, and dried. The intermediate is neutralised with calcium hydroxide or sodium hydroxide and spray-dried. The acid step destroys the micelle, and the cation used to neutralise the casein remains in the powder.

Micellar casein takes the other route. Milk is filtered through a membrane that holds back the casein micelle and lets lactose, whey protein and part of the minerals pass; the retentate is washed, concentrated and spray-dried. The micelle, with its native colloidal calcium phosphate, is still there. A certificate that says only “casein” has not named the material.

The three casein forms side by side

Casein forms · what changes with the grade
PointCalcium caseinateSodium caseinateMicellar casein
CAS number9005-43-09005-46-39000-71-9
ProcessAcid casein, calcium hydroxideAcid casein, sodium hydroxideMicrofiltration of skim milk
Protein, dry basis≥90.0%≥90.0%≥80.0%
CationCalcium 1.0–1.5%Sodium 1.0–1.5%Native micellar calcium; not specified as a range here
Ash≤4.0%≤4.0%≤7.0%
In waterDispersible; opaque, slightly viscousFreely soluble; slightly turbidDispersible; opaque, micellar
Label nameCalcium caseinate; milk declaredSodium caseinate; milk declaredMicellar casein; milk declared

Two cautions follow. A similar protein figure does not mean a similar ash or mineral load: the cation moves the nutrition panel, and the ash ceiling is the quickest sign of a caseinate. The calcium figures are also not directly comparable. Calcium caseinate carries the calcium added at neutralisation; micellar casein carries the native calcium of the micelle, which the micellar sheet does not state as a range.

The powder, the mixer and the dispersion

The catalogue form is a spray-dried powder at 80 mesh, with at least 95% passing, and it can be instantized on request. Agglomeration builds larger, porous particles that wet faster and throw less dust; it also lowers bulk density, which changes fill weight and scoop volume. A standard grade is simpler to make and harder to disperse without lumps.

Calcium caseinate disperses rather than dissolving. The dispersion is opaque and slightly viscous, and it is not a clear solution at any ordinary solids load. A formulator who expects the clarity of sodium caseinate should start with the sodium salt; in a bar or a shake, the colloidal body can be the point.

pH decides as much as the powder. At about pH 4.6 the casein reaches its isoelectric point and aggregates; an acidified drink needs a stabiliser and a trial with any casein form. At neutral pH the dispersion is stable but viscous, and heat can raise the viscosity further. Test the mixer, the solids load and the heat process together; a result in water does not predict the finished drink. The methods section explains the dispersion and mineral tests.

How much protein and calcium the formula carries

At 90.0% protein on a dry basis and 6.0% moisture, the powder is about 84.6% protein as weighed. The calcium range of 1.0–1.5% makes the same serving a calcium source as well as a protein source.

Protein and calcium per serving · calcium caseinate at catalogue limits
PowderProtein as weighedCalcium
5 g4.2 g50–75 mg
10 g8.5 g100–150 mg
20 g16.9 g200–300 mg
30 g25.4 g300–450 mg

A 20 g serving supplies 200–300 mg of calcium, which is 25–38% of the EU nutrient reference value of 800 mg and 15–23% of the US Daily Value of 1,300 mg. A 30 g serving supplies 300–450 mg. The calcium is real and belongs on the nutrition panel.

It is not a calcium premix. At 1.0–1.5% calcium the powder is mostly protein, while a mineral ingredient delivers calcium at tens of percent. A formulator who needs 500 mg of calcium from this powder would need 33–50 g of it. Use the caseinate for protein and body, and calculate the calcium it brings.

Specification lines for the grade

  • Form and process: calcium caseinate, acid casein neutralised with calcium hydroxide, spray-dried.
  • Protein ≥90.0% dry basis, Kjeldahl N × 6.38; calcium 1.0–1.5% as elemental calcium, method named.
  • Moisture ≤6.0%, ash ≤4.0%, fat ≤1.5%; ≥95% through 80 mesh or the instantized equivalent.
  • Dispersion test agreed with grams per 100 mL, water temperature, shear and standing time.
  • Milk allergen statement and the contaminant limits on the COA page.

Dispersion is the line most often left vague. Agree the test and the result format; without them, two suppliers can both claim good dispersibility and mean different things.

When another casein form is the better choice

Choose sodium caseinate when the formula needs a true solution, a high solids load in a neutral drink, or the emulsifying behaviour of the sodium salt, and the label can carry the sodium. Choose micellar casein when the label has to say micellar, when the native micelle is wanted, and when the plant can hydrate it. Choose calcium caseinate when a colloidal body is wanted, when the calcium fits the label, or when the sodium load has to come down.

None of these choices should be made on the protein percentage alone, because the two caseinates read the same 90%. The decision is four lines side by side: form and process, cation and ash, dispersion in the real mixer, and ingredient name on the label. The calcium caseinate versus micellar casein page takes the solubility, mineral and label questions further; the product hub carries the catalogue specification; the sodium caseinate page and the micellar casein page give the other two sides. The quality page describes release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation